TechRadar Verdict
This impressive hub enables you to connect multiple accessories to your laptop via a single cable. Speeds are capped at 10Gbps in total, with each device consuming part of that bandwidth. The SD card reader is also limited to UHS-I. However, the premium build, boost to 10 ports, power passthrough and impressive 2.5Gbe network connection balance performance, build and cost exceptionally well.
Pros
- +
2.5GbE Ethernet
- +
125W pass-through
- +
Connection through a single cable
Cons
- -
SD reader is UHS-I
- -
Speed slows with more connections
- -
Gets warm under load
Why you can trust TechRadar We spend hours testing every product or service we review, so you can be sure you're buying the best. Find out more about how we test.
Plugable 10-in-1 USB-C Hub: 30-second review
The Plugable USBC-10IN1E is a USB hub that, once plugged into your machine, usually a port-limited laptop, expands the port selection from one or two to 10.
In this test, I plugged the hub into several machines, including the Asus ProArt PZ14 - a tablet PC with only two USB-C ports that with the addition of the hub, turned a machine that required careful port rationing into a full desk setup with monitor output, Ethernet, keyboard, mouse, storage, and charging, and all connected through a single cable. The same result followed with the MacBook Air M3 and Pro M1 Max, for which the design matches perfectly.
The space-grey metal body of the hub gives it a clean aesthetic that matches Apple hardware, and at 109g and 216mm, it slips into any laptop bag neatly, although its length can be a little tricky to accommodate in a standard backpack pocket.
Connecting the hub to your chosen machine is easy enough with a single 17cm USB-C that enables you to tuck the hub neatly behind the machine. As I maxed out the ports during the test, I was also pleased to see that the port spacing along the hub's row of ports, which are all positioned along one side, enabled all ten connections to be used at the same time without the plugs blocking each other.
Through the test, the features that impressed me the most were the 2.5GbE Ethernet port that enabled fast wired network connections in the studio and office and the HDMI 2.1 output that enabled the hub to be used with my 4K monitors without reducing their potential resolution. For that alone, this is one of the best docking stations around.
The one surprise was that the SD card reader is only UHS-I rather than UHS-II, which features on the company's cheaper Plugable 9-in-1. If you’re a photographer offloading files from a Sony A7 IV, the reader works, but it is not the fastest option available; it’s still good if your laptop lacks port connectivity as standard.
Plugable 10-in-1 USB-C Hub: Price and availability
- How much does it cost? From $74
- When is it out? Available now
- Where can you get it? Directly from Plugable or Amazon
The Plugable USBC-10IN1E is priced at $84 USD and is available directly from Plugable's website, as well as retailers including Amazon.com, Best Buy, and Staples.
However, outside the US, I'm not seeing much availability at all.
- Value: 4.5 / 5
Plugable 10-in-1 USB-C Hub: Specs
Connection: USB-C 3.2 Gen 2 (10Gbps), 17cm/0.56ft
Video: HDMI 2.1 (4K 144Hz)
Power delivery: USB-C PD 3.1 EPR, 140W input / 125W output to host
Ethernet: 2.5Gbps
USB-C data: 2 × USB 3.2 Gen 2 (10Gbps, data only)
USB-A data: USB 3.2 Gen 2 (10Gbps, BC 1.2 charging) + 2 × USB 3.2 Gen 1 (5Gbps)
SD card reader: SD UHS-I + microSD UHS-I
Dimensions: 216 × 34 × 15mm
Weight: 109g
OS support: Windows 10/11, macOS 11+, ChromeOS 100+
Plugable 10-in-1 USB-C Hub: Design
When I put the USBC-10IN1E next to most of the USB hubs that I regularly use, the one notable feature aside from the huge array of ports is that it’s noticeably longer, at 216mm; it’s roughly the width of a 14-inch MacBook. This length is able to contain all those ports, an amount that is usually restricted to either a desktop machine or, more commonly, a powered USB dock.
Taking the hub from the box and the styling is instantly recognisable with Apple; the main casing is space-grey metal and gives the hub a premium feel as well as ensuring that it feels good and durable.
Connecting the hub to your chosen machine, Mac, PC or ChromeBook is made through the 17cm cable that’s an integral part of the accessory and and therefore non-removable. I like this design as it means the hub is all together and you won’t lose the cable or mix it with another in transport.
In use, that cable is also long enough to tuck behind either the Asus ProArt PZ14 or MacBook Air M3, keeping the sides of the workspace clear.
Port spacing along the hub is well thought through, with all ten connections: two USB-C, three USB-A, HDMI, Ethernet, SD, microSD, and the PD pass-through, all arranged so they can be occupied without the next cable blocking them. This isn’t always the case with compact hubs.
Through the test with SSDs, a monitor, controller, and several other accessories connected to the hub, did run warm under the load, the build of the hub with the aluminium casing was able to dissipate the heat well.
If you regularly plug accessories into your laptop and want more ports, then the Pluggable is a great option, especially with the simple design, plug-and-play nature and the fast wired network potential.
- Design: 4 / 5
Plugable 10-in-1 USB-C Hub: Features
The Plugable 10-in-1 USB-C Hub is a USB-C bus-powered hub with a 10Gbps bandwidth. This bandwidth is shared by the 10 ports, so each new accessory that’s plugged in takes a portion of that bandwidth, with the older USB-A 3.2 (Gen1) taking a small amount and the USB 3.2 Gen 2 (10Gbps) having the potential to take all of it.
In reality, in use, it all balances out, and the range of ports opens up direct connections for a host of laptops that are notoriously limited on port space, often just offering a couple and one that is usually taken up by the power supply.
This hub offers a staggering 10, which includes an HDMI 2.1 port that supports up to 4K at 144Hz or 8K at 30Hz, though the available resolution and refresh rate depend on the host machine's video output capabilities. The ProArt PZ14 and MacBook Pro M1 Max were both tested at 4K 60Hz via the Lepow TriScreen Pro, which is the display's maximum resolution.
The HDMI 2.1 modes require DP 1.4 with DSC on Windows (12th Gen Intel and later) or macOS 26 with M1 Pro/Max, M3 or newer on Mac. If you need 4K 144Hz, checking that your host hardware meets this specification is a given.
One of the surprises for the hub is the inclusion of the 2.5GbE Ethernet port, which means that when connected to the UGREEN DXP4800 GT NAS during the test, the hub delivered approximately 150 MB/s over the network.
Pass-through charging at up to 125W output worked with the ProArt PZ14's 65W power supply plugged into the hub's PD port. The PZ14 charged normally throughout the test with the hub as the sole connection. The 140W EPR input requires a PD 3.1 EPR-compatible charger and cable to deliver the full 125W; with a standard 65W charger, the output is limited, but matched the laptop I had connected.
The two USB-C 10Gbps ports are data-only, which means that they can’t be used for video output. Video output is catered for by the HDMI.
A nice addition and quite common for a hub is the SD and microSD readers, although these are both UHS-I. When checking the website, I noted that the cheaper Plugable 9-in-1 ($49.95) includes a UHS-II SD reader, which, for photographers shooting on Sony A7 IV UHS-II cards, might be a better option despite the drop in ports.
As you’d expect from a hub of this type, there are no drivers needed on either Mac or PC, and during the test, the ProArt PZ14 (Windows 11 Home) and the MacBook Pro M1 Max (macOS) recognised all ports without issue.
- Features: 4.5 / 5
Plugable 10-in-1 USB-C Hub: Performance
As the hub is bus-powered, essentially it draws power from the host machine through the USB-C cable that’s a permanent fixture, there’s no need for any type of external power supply. Therefore, getting started simply involves plugging in, and then the hub is instantly recognised and ready for use,
Once connected, all 10 ports share that single USB 3.2 Gen 2 (10 Gbps) connection, which means that if you use all ports at the same time, then the bandwidth is split between almost all, with two exceptions.
The HDMI output uses a separate DisplayPort Alt Mode channel, and its bandwidth is not limited by USB activity, so even if all other ports are in use, you won't see any effect on the visuals on screen.
The Ethernet port also uses a separate controller channel. But the rest, the five USB data ports, two SD card slots, and PD pass-through, all share the 10 Gbps USB pipeline.
In practice, this means high-speed transfers when you plug several drives, readers and accessories are less than that that headline 10Gbps, but in real terms this isn’t usually an issue. On the MacBook Air, for example, I found that plugging power and a CFExpress Type-B reader into the hub, and then the Crucial X10 into the machine, offered the best performance when it came to transfer rates, compared to having both plugged into the hub.
Checking out the difference in performance, I transferred files to both, then downloaded those files to the internal SSD of the MacBook Air M3. Individually, copy one then the other, the rates were Crucial X10 Read: 868MB/s Write: 792MB/s, and the Lexar 1800x read: 88MB/s and Write: 76MB/s. With both in use, the speed Crucial X10 Read: 782MB/s Write: 771MB/s, and the Lexar 1800x read: 87MB/s and Write: 60MB/s. The actual drop in speed with two storage devices was minimal, and throughout the test, I found that the 1GbE bandwidth was more than sufficient for most day-to-day tasks.
I also discovered that some SSDs, such as the Seagate Five Vault and the LaCie Rugged Pro5b, had too great a power draw from the USB-C 3.2 Gen2 ports to be used and needed to be plugged directly into the machine. It’s also worth noting that even with a power supply connected to the pass-through port, this still did not enable these higher-demand drives to be directly attached.
The best approach is, of course, downloading one device at a time rather than running multiple transfers together, as this avoids that bandwidth bottleneck.
Having recently upgraded my network to 10Gbe, it’s great to see a hub like this use 2.5GbE Ethernet rather than the more standard 1GbE. This means that I can connect directly from the hub into my switch and then to the Ugreen DXP4800 GT.
This connection managed 150 MB/s, which was fast enough for some light network editing, although doing so does warm up the hub more than the other connection types when in use. Still, that heat is well handled and warm rather than hot.
The HDMI output worked as expected and enabled me to connect the hub directly into a Lepow TriScreen Pro monitor, with the visuals seeming stable through the test.
What did stand out was the cross-platform capability of the hub as it seemed to work identically on the MacBook Air M3 Max and the Asus ProArt PZ14.
- Performance: 4 / 5
Plugable 10-in-1 USB-C Hub: Final verdict
The Plugable USBC-10IN1E is a neat hub that enables port expansion for today's slimline laptops and just adds a convenient and easy way to connect multiple devices and accessories to those machines. The single body design and fixed cable make it easy to pop into a kit bag and take with you, or leave connected to your workstation, and the design is durable in the first instance and aesthetic in the other to be suited to both uses.
It can’t be stated enough how much more convenient it is to have a single cable that connects to the keyboard, mouse, monitor, Ethernet, charging, and storage to your machine, and the fact that it can be moved between the ProArt PZ14 and MacBook Pro M1 Max by unplugging and replugging a single connector just makes working across multiple machines that much easier.
The 2.5GbE Ethernet is a great feature for creative professionals, and if you look for a dedicated 2.5GbE adapter, then the price for a decent option and then for this isn’t too different. Then there's the HDMI 2.1 support for 4K 144Hz displays, which is again a step up from most other hubs of this type.
The UHS-I SD card reader is disappointing, especially as you’re paying more for the premium model, and it features a slower card reader than the cheaper version. Plugable also prove some great software additions for their range of Docks, and it would have been great to see an option that worked with the hub, primarily a one-click ejects all option for Mac users.
For the price, the USBC-10IN1E is a great value if you’re someone who regularly switches between machines or needs to expand a two-port laptop into a full desk setup. While it does have limitations compared with a powered dock, through the test, it proved to be one of the best single-cable hubs I’ve tested.
Should I buy the Plugable 10-in-1 USB-C Hub?
Value | For $84, with 2.5GbE Ethernet, HDMI 2.1 and 125W pass-through, this offers exceptional value | 4.5 |
Design | The space-grey metal build, decent port spacing, and 17cm cable make it a great option in the office or out. | 4 |
Features | The 2.5GbE and HDMI 2.1 are surprising additions at this price; it’s just a shame that the SD slots are UHS-I rather than UHS-II. | 4.5 |
Performance | The hub is able to balance the bandwidth well, and through the test, even when downloading from multiple devices, there was only a marginal drop in speed. | 4 |
Overall | This is the best-spec’d bus-powered USB-C hub I have seen at this price and all at a great price for the volume of ports. | 4.5 |