As noted in my Ninja Creami Swirl review, with the right ingredients, your frozen dessert can help you meet your protein goals. I have tried dozens of recipes and found that I really don't care for the taste or texture of the ready-made protein shakes and powders that many high-protein recipes call for. Plus, they are quite expensive, often around $3 / £2.50 / AU$4.50 per serving, not counting any other ingredients you might add.

Many recipes also call for pudding mix, which is supposed to help with texture, taste, and added sweetness, but I'm not a fan of those either, so I searched out some options that provide a decent amount of protein without any of those products — just real food.

Just yogurt

The obvious option is just to take a tub (or two) of your favorite yogurt, dump it into the Ninja Creami pint, and freeze. Spin it on the Yogurt setting and you get a nice ice cream texture. The key is to use a yogurt that you really like, because the flavor doesn't magically change into ice cream, just the texture! The image above is two tubs of simple vanilla Greek yogurt. Keep in mind that freezing anything dulls the sweetness, so you might want to add a touch of your sweetener of choice before freezing, or add a sweet mix-in, such as cookies or chocolate.

Cherry-vanilla yogurt

Yogurt (or cottage cheese) and fruit is always a great combo. One of my favorites is this simple recipe:

Cherry-vanilla frozen yogurt:

3/4 cup dark sweet frozen cherries

1 cup Greek vanilla yogurt

Blend first and then freeze for 24 hours. Spin it on the Frozen Yogurt cycle. If desired, add more cherries for the Mix-in cycle.

I rarely actually blend mine first, but it's probably better for your machine if you do. This is a favorite I make over and over, and it's simply delicious. Sometimes I add 1/4 tsp of almond extract before freezing for a heightened flavor. I also sometimes add more protein and texture by running a small handful of nuts in the Mix-in cycle.

Pear-vanilla yogurt

This one sounds a bit odd, but it's so good.

Pear-vanilla yogurt:

2 tubs of Greek vanilla yogurt

1 tub pears

No need to blend, just mix and freeze for 24 hours. Spin on the Frozen Yogurt cycle.

Canned fruit is very soft, which is why you don't need to blend it. You can use any fruit here, it doesn't have to be pears. They all work well. You can try different yogurt flavors, too. Canned pineapple with coconut yogurt is a tasty combo, for example. And if you don't have tubs like I used, you can just measure out a roughly 2:1 yogurt to fruit ratio to the max fill line.

Chocolate Cottage Cheese Ice Cream

I have tried many chocolate 'protein ice creams' and haven't yet hit on that perfect recipe. This one is pretty good, with great texture. Be sure to taste it before freezing, in case you want to add more sweetener. User a sugar-free sweetener if you want to cut calories. If you prefer whole foods, try honey, maple syrup, or agave syrup. You could even just use a few dates.

Chocolate Cottage Cheese Ice Cream:

1 cup cottage cheese

3 tbsp cacao powder

2-3 tbsp sweetener of choice

2 tbsp almond butter

1 tsp vanilla extract

Blend well and freeze for 24 hours. Spin on the Light Ice Cream setting.

Add nuts, cookies, and/or chocolate on the Mix-in cycle if desired. I mixed in a few chocolate chips. If the cottage cheese is too salty for you, or you just don't like the taste, you could use milk or Greek yogurt instead. You can even do some combination of the three. The cottage cheese does give a nice texture, but you don't need the full cup to get it. Even a quarter cup helps.

And more

I have several high protein recipes in my recent article, healthier recipes for your Ninja Creami, including a pistachio ice cream recipe I particularly like and a banana nut ice cream I eat quite regularly. I also have some high protein options in my article about eating ice cream for breakfast!

I know my recipes tend to be dairy-forward, because that's what I like, but there are other options out there. I've seen bean-based and tofu-based recipes, but haven't had the guts to try them.

There are other additions to you can blend into any favorite recipe, such as hemp seeds, chia seeds, and flax seeds. Just a tablespoon added to any recipe will increase the protein and other nutrients without doing much of anything to the flavor of your ice cream.

Following the launch of Dyson's first ever compact hair dryer, the Supersonic Travel, I spent four weeks putting it through its paces, including during a trip to San Francisco — you can read about this in depth in my Dyson Supersonic Travel review.

What I kept coming back to was how similar it seemed to Dyson's Supersonic Nural, despite there being a $150 / £150 / AU$300 gap between the two. Both use the same motor and the same intelligent heat control technology. Both use the same magnetic attachment system, meaning any nozzle or diffuser from either machine works on both. And both deliver the same smooth, frizz-free finish that Dyson has become known for.

I've tested many of the best hair dryers on the market, and Dyson consistently sits near the top. So if the technology is this similar, what exactly are you paying the extra cash for — and is the Nural worth it? I tested the two side by side. Here's what you need to know.

Dyson Supersonic Travel vs Supersonic Nural dryer: efficiency

On sheer drying power, the Nural wins. It's a full-size dryer with full airflow, and on my fine, mid-length hair it dried in around two and a half minutes on high heat. The Travel took around four minutes in the same conditions.

Four minutes is fast for a travel dryer — faster than every hotel dryer I've used and faster than some standard home dryers too. The finish was smooth and shiny every time, which is the more important result. But the gap is significant, and if you have thick or long hair that already takes 15 or 20 minutes at home, you'll feel it a lot more than I did.

Both have a 110,000 RPM motor, and both use a built-in thermistor sensor that continuously monitors air temperature to prevent heat damage and protect your hair's shine.

Interestingly, the cheaper Travel measures temperature more frequently than the pricier Nural — over 100 times per second versus 40. However, where the Travel uses it as a protective measure, the Nural uses it in more advanced ways for its Scalp Protect Mode. This mode uses a network of Nural sensors and an infrared beam to measure the distance between the dryer and your scalp in real time, automatically reducing heat and airflow as it gets closer to maintain a consistent 131 F / 55 C at the roots.

Winner: Dyson Supersonic Nural

Dyson Supersonic Travel vs Supersonic Nural dryer: design & comfort

Both the Nural and Travel look unmistakably like Dyson products. They have the same cylindrical head, narrow handle, and magnetic barrel as the entire Supersonic range. I tested the Travel in Ceramic Pink/Rose Gold and the Nural in Red Velvet/Gold, and both have a stylish soft matte finish.

The biggest and most obvious design difference is in size.

The Nural weighs 1.5lbs / 684g and measures 3.8 x 3 x 11.3 inches / 9.8 x 7.7 x 28 cm. The Travel is 32% smaller — at 2.7 x 2.8 x 8.7 inches / 6.8 x 7.1 x 22.2 cm — and almost half the weight. This makes it small and light enough to drop into a handbag without rearranging everything around it and I carried the Travel to San Francisco in a tote bag alongside my laptop and it barely registered.

Both put airflow and temperature buttons on the rear of the barrel, with LEDs above each button showing your current setting. On the Nural, these LEDs change color as you cycle through settings to make it easier to see, at a glance, what setting you're on. The Travel's stay white, making it harder.

Beyond this, the Nural offers four heat settings plus three airflow speeds. The Travel has three heat settings and two airflow speeds. On the Travel, its cool shot requires sliding the power button upward past its 'on' position. This will be familiar if you own a Dyson Airwrap i.d but if you don't, this feature won't feel obvious the first time you use the Travel.

The Nural gives you meaningfully more control over both heat and airflow, which matters if you have multiple hair types or needs in your household, or if you regularly switch between drying and styling with different attachments.

Cord length is 9.2ft / 2.8m on the Nural and 6.6ft / 2m on the Travel, and neither folds. The Travel's cord is longer than I'd like for a machine sold primarily on portability but this longer length does make it easier to use in a hotel room when the plug socket aren't always in the most useful places.

Winner: Draw – even though the Nural has some standout design benefits compared to the Travel, they fit different needs: the Nural is better designed for home, while the Travel is better for everywhere else.

Dyson Supersonic Travel vs Supersonic Nural dryer: special features

The Travel's standout feature is auto-voltage. It adapts automatically to any supply between 100V and 240V without the need for a converter or a switch. I used it in San Francisco with a standard plug adapter and there was no drop in power, change in noise or overheating.

The Nural counters with Scalp Protect Mode, which uses proprietary sensors to detect proximity to your scalp and automatically drops the air temperature. When you pull the dryer away, it returns to your selected setting. This setting works in the background, and over months of daily use I haven't once scorched my roots on a high heat setting. For anyone with a sensitive scalp, fine hair, or hair growth concerns, it's a functional benefit rather than a convenience feature.

The Nural also has Attachment Learning, which recognises which nozzle is fitted via RFID chips and remembers your preferred settings.

For example, if you swap to the diffuser, the Nural will automatically drop to your usual diffuser heat and speed. The Pause Detect feature then cuts the airflow when the dryer is put down and resumes when you pick it back up.

The Travel has neither of those features but it is compatible with the entire Supersonic and Supersonic Nural attachment range. If you already own the Nural, you can pack your existing nozzles and diffuser and use them on the Travel.

Winner: Dyson Nural – the Travel's auto-voltage is the most widely practical feature across the two dryers but the Nural is a much more advanced choice.

Dyson Supersonic Travel vs Supersonic Nural dryer: specs

Should I buy the Dyson Supersonic Travel or Supersonic Nural dryer?

Buy the Dyson Supersonic Travel if...

✅ You travel frequently and your hair matters to you: Hotel dryers are a lottery. The Travel gives you consistent Dyson-quality results wherever you are.

✅ You already own a Dyson Supersonic or Nural: The attachment compatibility means you're not buying a second set of nozzles – just a travel body for your existing routine.

✅ You have fine or mid-length hair: The reduced airflow won't be an issue for finer hair types. Four minutes is still fast, and the intelligent heat control means the finish is just as good as you'd get from a full-size dryer.

Buy the Dyson Supersonic Nural if...

✅ You want the best Dyson for home use: Full airflow, smarter controls, color-coded LEDs and five attachments make this the more complete package for everyday drying.

✅ You have a sensitive scalp or fine hair at the roots: Scalp Protect Mode works in the background and over months of daily use, the difference in root and hair health is noticeable.

✅ You dry your hair every day: The Nural's Attachment Learning and Pause Detect are small features that add up to an easier daily routine.

I test over a dozen of the best coffee makers every year here at TechRadar, but having a small kitchen means I have to be very picky about which I choose to buy myself. The problem is, I love both drip coffee and espresso equally. I'd happily pick up a compact espresso machine and a quality drip coffee maker such as the Breville Luxe Brewer Thermal, but that would mean sacrificing valuable food prep space and, potentially, not having enough work surface available for rolling pastry and kneading dough.

Of course, a kitchen with no space in which to make pies or bread would be tragic — but, thankfully, it doesn't have to come to that because the Ninja Prestige DualBrew System can handle all my espresso and drip coffee-making needs in one convenient package.

I first tested the DualBrew System (known as the Ninja Espresso and Coffee Maker Barista System in the US) about nine months ago, and it's still the most impressive two-in-one coffee system I've ever used. It isn't a particularly glamorous appliance to have sitting on your counter — it's designed for function rather than looks — but it's enormously practical and has clearly been designed by people who know and love their coffee.

On the left of its roughly cuboid-shaped body, you have a fully featured drip coffee maker, with a standard-sized brew basket and toughened glass carafe. It has all the features you'd expect from a good-quality standalone brewer, including different intensity settings (regular, rich, or over ice) and a timer to start brewing when you wake.

However, there are also some great additions, such as a drip-stop system that means you can safely remove the carafe partway through brewing without making a mess, as well as a fold-down drip tray so you can brew directly into a travel cup rather than the carafe if you want your coffee to-go in the morning.

Some drip coffee makers use of a double-walled insulated carafe to keep your drink at the ideal temperature after brewing, whereas others use a hotplate. The DualBrew System is in the latter camp, but unlike any other drip coffee maker I've tested, it has a smart hotplate that doesn't just heat your coffee consistently, but instead turns on and off to help maintain the right temperature without stewing your brew. It also turns off automatically when you take the carafe away.

Espresso is handled on the right-hand side of the machine. The DualBrew System uses Nespresso Original-style coffee capsules, which means there's a huge array of different beans, blends, and roasts to choose from. Nestlé no longer owns the patent to this type of capsule, so any company is free to package its own freshly ground coffee in these little pods.

Personally, I like to use capsules from my local roastery, and an espresso made using these pods in the DualBrew System tastes almost identical to the same beans prepared with a manual coffee maker.

There's a choice of three drink sizes, and the espresso machine has an adjustable-height drip tray so you can use any cup you want. When you're done, the spent pod drops into a bin, ready to be emptied later.

The only downside of the DualBrew System is the lack of a steam wand (which makes sense, since there's no pressurized boiler here). Instead, there's an electric whisk that folds out from the rear of the machine. This doesn't heat your milk, but the DualBrew System offers a handy guide that advises how long to heat your milk for in the microwave, and how to whisk it for different espresso drinks. It's not the same as steam, but it's fine in a pinch when you don't have much space.

If that's a deal-breaker, a standalone milk frother such as the Dreo BaristaMaker or Smeg Mini Milk Frother will deliver more authentic results, and is small enough to tuck into the corner of a cabinet when it's not in use.

If you love coffee in all its forms but don't have acres of countertop space to spare, the DualBrew System provides everything you need in a single, neat package — and it's affordable, too. At the time of writing, it's available for $249.99 / £179, down from a list price of $279.99 / £249.99. You'll find all today's best deals at the bottom of this article.

• Google is expanding Gemini Live to the first-gen Home Mini speaker and Nest Hub smart display
• It rolled out in Gemini for Home early access, and requires a Google Home Premium subscription
• Google also increased Gemini's conversation memory window to 15 minutes

It’s a great day to be an owner of older Google smart home devices, now the company is rolling out Gemini Live to its two of its OG models.

Yesterday (July 23) Google unveiled a slew of Gemini for Home early access upgrades on its support page, but the one that has everyone talking is the arrival of Gemini Live, which is coming to the first-gen Google Home Mini speaker and Google Nest Hub smart display.

The update marks the next step in Google’s plan to expand the ubiquity of its live AI chatbot, which the company rolled out to the Nest Mini, Nest Audio, Nest Hub, and Nest Hub Max devices in October 2025. The new Google Home Speaker comes equipped with Gemini Live out of the box.

For users who are still going strong with their first-gen Google devices, we imagine this upgrade will be welcomed with open arms, but the one catch is that Gemini Live is paywalled behind the Google Home Premium subscription service, which costs a monthly fee of $10/ £8/ AU$15.

If you already have Google Home Premium and are part of the Gemini for Home early access program, you can now start conversations with your Home Mini and Nest Hub devices by saying ‘Hey Google, let’s chat’. The chime will indicate that Gemini is listening, and you can ask it anything such as recipe ideas, suggestions for an upcoming trip, or dive deeper into the most niche topics.

In addition to Gemini Live’s expansion, Google has upgraded Gemini’s conversation memory window to 15 minutes. “You can ask Gemini a follow-up question to a topic that was discussed during this window, and Gemini will understand the context,” the company details.

It’s refreshing to see that Google hasn’t completely given up on its early smart speakers and displays — even if the hardware is aging. Not often do you see tech giants acknowledge that old devices are still widely used, and Amazon is a classic example of this.

A few months back, the company came under fire for ending support for Kindles released from 2012 and earlier even though there’s a whole community of bookworms that still rely on these models — so Google is doing a better job than Amazon in that regard.

Signed up to Google Home Premium but unsure how to join the Gemini for Home early access program? We’ve got you covered.

First, you’re going to need to request early access, and you’ll need to make sure your Google Home app is updated to the latest version. From there, launch the app and tap your profile image or initial at the top right, select Home settings, and then Early Access. Follow the steps to request early access, and you’ll receive a notification when Gemini for Home becomes available for your devices.

You can also check region availability and other information on the Google Home and Nest help page.

• Ring had launched an updated Outdoor Camera and Peephole Camera 2K
• They will both go on sale in August 2026
• The Outdoor Camera is £99.99 (about $130 / AU$190), and the Peephole Camera is £79.99 (about $110 / AU$150)

Ring has announced two brand new smart security cameras, one for mounting outdoors and one for installing into the peephole of your door.

Let's start with the outdoor option first. The new Ring Outdoor Camera (2nd Gen) is available in both wired and battery versions. It has a wide-angle lens (140 degrees horizontal and 85 degrees vertical), and delivers 2K resolution with up to 6x enhanced zoom. It has B&W night vision, customizable privacy zones and motion detection, and you can talk to visitors via Live View and Two-Way Talk. If you subscribe to Ring Protect you can also get intelligent alerts and the ability to scroll back in time to rewatch footage. Wi-Fi is single-band Wi-Fi 4 using the 2.4GHz frequency band.

One of the big selling points here is easy installation: it's simple to mount the camera and it's designed to cope with temperatures from -20ºC to +50ªC, although Ring says the camera may temporarily turn itself off if it's in direct sunlight during extreme heat conditions.

The Ring Outdoor Camera (2nd Gen) has a list price of £99.99 (about $130 / AU$190) and it'll be available from August 12, 2026. Pre-orders are open now.

Ring Peephole Camera 2K: this peep is fairly cheap and fits in doors that are quite deep

The new Ring Peephole Camera 2K is more stylish than its rather boxy predecessor, with a more triangular shape and a good-looking speckled finish. It fits through the space where you'd normally have an optical peephole, and there's no need to drill, run cables or do anything at all as it's completely wireless and runs off a rechargeable battery. It's designed to fit peepholes from 12mm to 14mm in size and go through doors between 32.5mm and 60mm.

I think this is going to be particularly popular with flat dwellers, especially renters who can't make any physical changes to the property: simply unscrew the optical peephole, install the camera, and you can take it with you when you move. Don't forget to keep the original peephole somewhere where you can find it again, though.

Like the new Outdoor Camera (2nd Gen) the resolution is 2K with up to 6x enhanced zoom, Live View and Two-Way Talk, but there's no night vision here so you'll need to make sure the door is facing a well-lit area. Ring says its camera is tuned for low-light conditions, but this camera doesn't see in the dark like the Outdoor Camera does.

The field of view is 140 x 140 degrees to deliver 'head-to-toe' visuals, and the quick release battery is easy to remove for charging. Wi-Fi is Wi-Fi 4 on the 2.4GHz frequency band.

The Ring Peephole Camera 2K will be available from August 19, 2026, and pre-orders are open now. The list price is £79.99 (about $110 / AU$150).

Can't decide what kind of coffee you'd like in the morning? De'Longhi has just launched a new coffee maker that can prepare both hot and cold espresso drinks — and even drip coffee if you're in the mood for something different. The De'Longhi Magnifica Duo offers a menu of 20 preset drinks, which you can choose with a quick finger-tap.

If you want to fine-tune your coffee, there are three user profiles, which let you save drinks with custom size, intensity, and temperature settings.

The Magnifica Duo is a successor to the Magnifica Evo Next, which our reviewer Josephine Watson awarded four stars out of five. The Duo has a similar look, and should be just as simple to use, but with the ability to prepare authentic cold-extracted espresso as well.

Unlike some other bean-to-cup coffee makers, which pour a shot of hot espresso over a cup of ice, the Magnifica Duo extracts espresso using cool water directly from the tank and passes it through the freshly-ground coffee beans more slowly to achieve a mellow, but still well-rounded flavor without bitterness.

Not only that, the Magnifica Duo also has a pair of swappable carafes for preparing hot and cold milk foam, so you can easily make iced lattes and cappuccinos. It's the same LatteCrema Hot and Cool system used by the De'Longhi Primadonna Aromatic, and is quite ingenious.

With the Hot and Cool system, milk never enters the machine itself, so you don't need to worry about any buildup inside, and each carafe can be disassembled into a few dishwasher-safe parts for quick and hygienic cleaning. It works with both and plant-based milks too, and in my experience testing the Primadonna Aromatic it delivered excellent results with both.

The De'Longhi Magnifica Duo is available now for $999.95 in the US, and £699.99 in the UK. That's about AU$1,350, though it hasn't launched in Australia just yet. I'm hoping to test it soon to see whether it can earn a place in our roundups of the best coffee makers and best espresso machines.

• The Jura E10 is a new premium espresso machine from the Swiss brand
• It offers hot and cold brewing, syrup-infused foam, and Light Brew mode
• It's available now for £1,425 (about $1,910 / AU$2,720)

Jura, known for its luxury espresso machines, has just launched a new coffee maker that packs a staggering array of advanced brewing features into a surprisingly compact package. The new Jura E10 offers hot and cold brewing, syrup-infusion for flavored drinks, and a new timer that means the machine can start brewing when you wake so your favorite coffee is ready and waiting the moment you wake up.

The feature set sounds very similar to that of the Jura J10 I tested last year, which is still one of the most advanced coffee makers I've ever used. It poured a perfectly-extracted espresso, and its cold-brewed espresso was mellow and flavorful.

Its milk system was excellent as well, whether using hot or cold milk, but what impressed me most was the Sweetfoam system that mixes the syrup of your choice into the milk as it's dispensed.

Flavored coffees are usually made by pumping syrup into the cup before adding coffee and milk, which means the flavor is concentrated at the bottom. With Sweetfoam, the syrup is evenly distributed throughout the whole drink, which means you get the full flavor with every sip, and only need to use a very small quantity. You can use regular or sugar-free syrup, and during my tests I found it had the added benefit of stabilizing the milk foam so it lasts and lasts.

Perfect for small kitchens

Like the J10, the new E10 offers a huge menu of hot and cold drinks, but now they're organized into a color-coded menu that makes it easier to find the one you want.

These options now include Light Brew — a new feature not available in the J10 — which uses a smaller dose of coffee and a lower brewing temperature to prepare a drink with a less intense flavor that's ready to enjoy straight away.

The coffee-timing feature means the machine will start brewing your coffee automatically exactly when you want it to — a feature you'd normally only see on drip coffee machines. However, it's worth noting that this is only available if you also pick up the Jura Wi-Fi Connect V2 module, which adds wireless connectivity to your coffee machine and costs an additional £49.95 (about $70 / AU$100).

All of these brewing functions are packed into a surprisingly slim package that will slot more easily into small kitchens:

The Jura E10 is available now direct from Jura and a handful of third-party stores for £1,425 (about $1,910 / AU$2,720). It's currently only sold in Europe, but the rest of the E range is available in the US, so I'm expecting it to launch there in the coming months.

• The UK government has quietly revealed when plug-in solar will be legal
• The law change will come into effect from August 27
• The panels could save you up to £110 a year on your energy bills

The UK government has quietly revealed when plug-in solar panels will become legal to buy in the country — and the magic date is August 27.

The date (spotted by Engadget) is hidden away in these amended 'Plugs and Sockets' regulations for the UK. These are "coming into force" from August 27 and effectively legalise plug-in solar panels, which currently exist in a legal grey area.

Right now, it isn't legal to send electricity into a wall socket to power your appliances or other tech. But these amendments make a new exemption for so-called plug-in solar, provided the new kit meets some strict criteria.

Specifically, your solar setup can't output more than 800W of power and also can't "import electrical energy" from your house to be stored and used later. This date also isn't necessarily when we'll see plug-in solar panels — otherwise known as 'balcony solar' — go on sale, but refers to when they can be approved to go on shelves.

The government's research, which included a consultation that ended on June 30, suggests that plug-in panels could start at around £400, and save households up to £70-£110 a year on their energy bills. You also shouldn't need professional installation nor planning permission, unlike regular rooftop panels.

While the legal amendments have unfortunately come towards the end of the summer, it does mean the government will have hit its target of finalising plug-in solar legislation by the end of the season.

Where will you be able to buy them?

While retailers aren't committing to exact on-sale dates yet, some major ones have hinted to us that they'll be keen to stock plug-in solar kits as soon as possible.

John Boumphrey, UK & Ireland Country Manager at, Amazon said: "The Government's announcement on plug-in solar panels is a practical step that gives households a simple way to generate their own power, reduce bills, and contribute to the UK's net zero goals. We're looking forward to helping customers access this technology."

Lidl could be another store that supports the tech, given it's already launched its own cheap battery that's designed for solar systems in Germany. Georgina Hall, Corporate Affairs Director at Lidl GB, told us: “At Lidl GB, we are committed to making sustainable living affordable for everyone and we welcome the Government’s move to modernise regulations in the UK.

"Updating the regulatory landscape for this 'plug-and-play' technology is a positive step towards empowering British households to manage their energy costs and support the nation’s net-zero ambitions."

Last month, we also saw that Asda, Currys, B&Q, Wickes, and Screwfix had met with the Minister for Energy Consumers, Martin McCluskey, to discuss balcony solar panels. "Plug-in panels can be transformative for renters or those on lower incomes, so I welcome the conversation today with household names such as B&Q and Currys showing a huge amount of support for getting the panels in people's homes," McCluskey said.

So if you're interested in plug-in solar panels, you shouldn't be short of options from traditional high street names — let's just hope the sun is still shining by then.

Robot lawn mowers are growing in popularity, and with good reason. They're getting more advanced in features, easier to set up and use, and can be a huge time- and effort-saver... provided you pick the right model. There are plenty of options to choose from, spanning a range of prices and capabilities, and if you're new to the lawnbot world then it can be tricky to figure out which one you need.

This article is here to guide you through that process. I've pulled together five big questions to help you narrow down your options. And for added expertise, I've enlisted the help of KK Yin, Marketing Director at leading lawnbot brand Mammotion, whose insights you'll find throughout the piece.

#1. Do I need all-wheel drive?

"Everyone has a different environment for their lawn. So the first thing a customer should do is choose which kind of power system they need — for example, all-wheel drive or rear-wheel drive, or some the brands have front-wheel drive," says KK.

Rear-wheel drive will be perfectly fine if you have a relatively even and flat lawn, and will have no issue scaling relatively gentle inclines. However, if you have a very steep or uneven lawn, all-wheel drive (AWD) will help ensure the lawnbot maintains its grip without churning up your grass. Front-wheel drive is really only for flat lawns, and is a less common power system.

AWD tends to be reserved for larger, more premium robot mowers. However, at the start of this year Segway Navimow launched compact AWD model, with the suggestion that it would treat your turf more gently.

#2. Does my lawn have shaded areas?

Next, KK suggests figuring out which navigation method is best suited to the environment. "A customer should look at if they have shaded areas, the house is tall or they have trees in the garden. If they do, I suggest they don't choose an RTK positioning system. They should maybe choose a LiDAR model," says KK.

There are two major navigation systems for robot mowers. RTK, which uses satellites, can work very well if the lawnbot has a wide, uninterrupted view of the sky. However, if there are obstructions — such as those listed by KK — in the way, these can block the signal and lead to the lawnbot getting lost.

LiDAR is the system used by robot vacuums, and is relatively new in the robot mower market. LiDAR builds a picture of its surroundings by bouncing light off objects, so it's not well suited to wide-open lawns with no objects in them.

Broadly speaking, RTK will be a good choice in big, open yards, whereas LiDAR might be a better fit if you have a smaller, more cluttered yard. LiDAR models are often pricier, so if you can get away with an RTK bot, you might prefer to go with that option.

#3. How big is my lawn?

Many lawnbot models are available in a few different iterations aimed at different-sized lawns (typically indicated by a number after the product name). The difference is usually the battery capacity — a bot designed for a larger area will have a bigger battery, enabling it to cover more ground before having to return to its dock to recharge, thus making it more efficient.

"I think most users figure out that in one week they will mow maybe two or three times. So they need to work out how long it will take a product to mow their lawn once," suggests KK. With that information, you can work out if your mower will be efficient enough to keep up with your grass-trimming demands.

#4. Do I have more than one mowing zone?

"The next point, I think, is about multi-zone management," says KK. "Not all people have one big lawn — it's divided by the house, or the garden is split into different areas. That means they need to manage more than one mowing zone."

Pretty much every lawnbot will be able to mow multiple separate lawns, with the ability to create different maps in your app. However, some have more advanced multi-zone capabilities than others. One bot might be intelligent enough to handle a schedule where the lawnbot spends the morning in Zone A and moves to Zone B in the evening, and it might even be able to work out the optimal mowing patterns and cadence.

#5. How much setup do I want to do?

If you end up with a satellite-based lawnbot (see point #2), you might need to decide between a bot that comes with a separate antenna and one that does not. This RTK station is required to make the satellite information more accurate — so satellite positioning on its own might tell you where a bot is to within a meter or two, but add in a separate RTK receiver and it's more like centimeters.

Traditionally, you'd have this receiver in your own back yard. This adds an extra level of complexity to setup — the reciever needs to sit high up, with direct line of sight to satellites in the sky, and it also needs a power source. However, increasingly, we're seeing lawnbots that use a big, centralized RTK receiver that covers a large area. Mammotion calls this NetRTK. It's definitely a more low-effort option.

There are further features to look out for if you want the most straightforward setup. Some modern robot mowers have cameras and AI features that enable them to instantly create a map of their location, so you can just pop it on the floor and it'll be able to start mowing pretty much instantly. KK suggests these kinds of features are more of a nice-to-have, and advises focusing on the first four points first.

Reviews round-up

We've tested plenty of excellent lawnbots at TechRadar. Here's a taster of some of our favorites — tap the 'View details' button for more information, plus a link to our full reviews.

• Philips is rumored to be launching a new camera-based Hue Sync device for its TV backlights
• It removes the need for a pricey Hue Play HDMI Sync Box
• The 'Sync Screen' would be the first camera for the Philips Hue Play system

Philips Hue could be working on a new device for syncing your TV’s color palette to your backlights, giving you another option for illuminating your entertainment setup

Fabian of Hue Blog attended an online presentation hosted by Philips, and spotted a new Hue Sync device with an integrated camera that looks strikingly similar to rival devices like the Nanoleaf 4D.

The new gadget could be called ‘Sync Screen’, and may be unveiled at IFA 2026 in September. We don't know how much it will cost yet, but considering Philips Hue is a premium brand, it's likely the new device will sit in a higher price bracket than its competitors.

Just like other camera-operated TV LED lights, Philips’ version mounts to the top of a TV or monitor, and captures the color movements of the movie, show, or game on the screen. This movement is then processed and synced with backlights mounted behind the display.

From the image shared by Hue Blog, it seems that the Philips Sync Screen camera will only have one lens, but will likely be a fish-eye one to capture your entire TV screen — just like those used by rival devices.

You will almost certainly still need a Philips Hue Bridge to link the lights and camera to one another, but because the system camera-operated, you won't need a Philips Hue Play HDMI Sync Box or Hue Sync TV app subscription, which could make it a more tempting proposition.

As mentioned, Philips isn’t the first smart home giant to offer TV lighting gadgets like this, which aim to make your TV and gaming experiences more immersive by extending the colors from the screen onto the surrounding walls.

In addition to the Nanoleaf 4D light strips, the Govee StarPal Pro and the more recent Govee TV Backlight 3 Pro models are all camera-operated — the latter having a dual-camera system to capture more of your TV screen or monitor.

Philips has had quite an eventful 2026 already. In March the company unveiled its new OLED TVs, which are also the first native models for Dolby Vision 2, as well as its beautiful yet expensive ceiling light that mimics natural daylight. We’re just a mere two months away from IFA 2026, and I think the best is yet to come.

A new Google Home Display might be on the cards, but sticking to the traditional smart home hub format seems like a missed opportunity. What I really want to see this year is a new version of 2023's Google Pixel Tablet — and it would be a much better fit for a modern AI-powered smart home.

Google hasn't officially announced a new smart screen, but I think it's only a matter of time. Last year, Anish Kattukaran, Chief Product Officer for Google Home, said the company was still committed to the smart display format. "If you think about the properties of a smart display: a microphone, which means audio in, a speaker, so audio out. It’s got a screen, which complements a voice modality, you can interact with it and visualize information," he told The Vergecast.

"As I see where Gemini for Home is going and Gemini more broadly, all of the things Google is investing in building, for me it feels like almost the ultimate form factor to be able to deliver a really great home experience. So, that’s why we are going to continue to invest in that category, so I think it’s going to be awesome."

A smart home hub can be so much more than a speaker, screen, and microphone though, as the 2023 Google Pixel Tablet demonstrated — and I think a new version of that device would be an even better platform for Gemini than a Google Home Display.

The smart home untethered

If you're not familiar with the Pixel Tablet, it's essentially a full Android tablet specifically designed for use around the house. It doesn't have great battery life, and there's no SIM card slot for mobile data, but that's not a problem when you're never straying outside range of your home Wi-Fi network, or taking it far from its dock.

At first glance it looks just like a Google Home Display, but there's one big difference: while the Home Display is all one unit, the Pixel Tablet's screen lifts off its magnetic dock so you can carry it from room to room.

Unlike a Google Home Display, the Pixel Tablet isn't just a hub, either. Although it can be the heart of your smart home, providing quick access to your lights, switches, robovacs and cameras with quick voice controls, it's also a fully-featured Android tablet, with access to the whole Google Play Store. That means you can install your favorite web browser, stream movies from Netflix, or spend hours on YouTube on its 10.95-inch display. It has a reasonable front-facing camera as well, so it's ideal for Zoom calls with the family from the comfort of your sofa.

My Pixel Tablet lives on my kitchen table, where it serves as both a smart home hub and a second TV, letting me stream shows via BBC iPlayer at breakfast time, or use YouTube Music to play music while I work. The tablet's built-in speaker is quite tinny, but the one housed within its dock sounds surprisingly rich and well-balanced.

When it's time to make dinner, I can simply pluck it from its dock, stand it on the kitchen counter, and load my recipe app of choice, then in the evening, I can crash out on the sofa, adjust the lights, and finish my daily Duolingo session. You can't do that with a Home Display. Sounds good? It is — and it's now discontinued.

A smarter Pixel Tablet

So what would a 2026 Pixel Tablet look like? Well, apart from having Gemini pre-installed (naturally), it needs to function as a Thread border router, and its speaker needs a boost to bring it level with the new Google Home Speaker. Its 2,560 x 1,600px screen resolution is already respectable though (for comparison, the larger Amazon Echo Show 11's screen is 1,920 x 1,200px) and its weight doesn't matter considering it's not intended to travel outside the house, so I wouldn't worry about slimming it down much.

It would be nice to see a lower price, though. The original Pixel Tablet had a list price of $499 / £599 / AU$899, which is a hefty fee for a smart display. A cheaper Pixel Tablet might be wishful thinking, but considering you would need a Google Home Premium subscription to get the most out of Gemini, a lower asking price would make it a more tempting proposition.

There's a chance that Google might surprise me with a Google Home Tablet that can roam from room to room, but somehow I doubt it. Apple's vision for the future seems to involve multiple screens scattered throughout your home, while Amazon Echo devices are so affordable, it's easy to justify buying one for each room. We'll have to wait and see.

You might be thinking more about BBQing and less about air frying with the current weather, but with this deal you can have the best of both worlds. It's for the Ninja Foodi Max, which is now on sale at Amazon for £179.99 (was £229.99). That's the lowest price we've seen since Black Friday.

The Ninja Foodi Max is a highly-rated twin-drawer air fryer that can cook two foods at once, produce crisp, evenly browned results, and, after enjoying all that gorgeously cooked food, is super easy to clean.

And if you're concerned about eating too much oil or the cost of it, Ninja claims that the Foodi Max dual-zone air fryer reduces the amount of oil required by 75%. This is the complete package, now at a low price.

Today's best Ninja air fryer deal

Ninja sells a wide range of air fryers, and two of them boast a very similar design. You've got this deal for the Ninja Foodi Max that we awarded four stars and the very similar Ninja Foodi Dual Zone Air Fryer that we gave a full five stars. The bottom line is that Ninja knows what they're doing.

The Foodi Max is a 6-in-1 beast that offers, you guessed it, six unique cooking functions: Max Crisp, air fry, roast, bake, reheat, and dehydrate. This high level of versatility alongside the large 9.5L capacity means you'll be able to cook a wide range of meals for the whole family or when entertaining.

If the footprint of the Foodi Max is too big for your kitchen, then why not consider the Ninja Double Stack with its two-tier design? Alternatively, take a look at the latest air fryer deals, and I'm sure you'll find an air fryer to suit your requirements at a price you love.

Eufy Omni S2: two-minute review

Eufy’s latest flagship robotic vacuum and mop, the Omni S2 is a hugely impressive appliance that combines excellent mopping with brilliant vacuuming to create one of the best home cleaning systems you can buy. It also self-cleans so thoroughly that, after several weeks of daily use, the dust bin, rollers and mop still looked like new.

The Omni S2 uses warm water to clean its spinning mop as it goes, while also scraping away dirt and using cyclone technology to whisk dust more efficiently into the onboard bin, instead of leaving it to clog up the filters. Water is ozonated in the base station to further improve cleaning performance, and there’s an integrated detergent system too.

The robot itself can even be fitted with a fragrance diffuser, which makes your room smell nice after every clean; three different scents are included in the box and, along with the detergent, and can be replenished from Eufy’s website.

It navigates well, mostly avoiding contact with walls and doors while driving very closely to all manner of obstacles without pushing them around, driving over them or ingesting them. The S2 is good at climbing over raised carpets, rugs and door thresholds — something the Omni S1 struggled with – and the app does a great job of quickly mapping your home, with a simple editing system for labeling every room correctly, and even adding virtual furniture.

I was impressed by how quiet the Omni S2 is, even with its powerful Cyclone mode engaged, and how the base station doesn’t sound like an Airbus when emptying the robot. It’s a very expensive product, but one that looks good and performs extremely well.

Eufy Omni S2: price and availability

• List price: $1,599 / £1,599 / AU$2,299
• Launched: March 2026

Just two years on from the launch of the Omni S1 Pro, Eufy now has the Omni S2. This is now the company’s flagship robotic vacuum and mop, with a price, performance and feature set to match.

It carries a recommended retail price of $1,599 / £1,599 / AU$2,299, making it £300 more expensive than the S1 pro, which remains on sale. That’s an awful lot of money for a vacuum cleaner — especially when

Eufy’s own range of robovacs starts under the £150 mark, and one of my favourites — the X10 Pro Omni vacuum and mop — is a comparative snip at £599.

What does the extra £1,000 get you with the S2? More power, of course, with greater suction thanks to Eufy’s new AeroTurbo 2.0 tech, improved intelligence, greater threshold clearance, a more powerful mop, better computer vision, a self-cleaning mop, electrolysed water, integrated detergent and even a built-in fragrance system with three included scents to pick from.

An additional cost to bear in mind is Eufy’s replacement parts kit. The brushes, bags, mops and rollers of all vacuum cleaners need replacing, so ongoing costs aren’t unusual, but Eufy likes to charge plenty. A complete kit for the S2 is £79.99. Premium parts for a premium robovac, I suppose. More welcome is Eufy’s new two-year warranty, which applies to all robot vacuums launched in 2026 and doubles the previous coverage.

• Value score: 3.5/5

Eufy Omni S2: specifications

Eufy Omni S2: design

• Docking station with charger, dust bag, water tanks and mop drying
• Rotating, self-cleaning mop
• Integrated detergent and fragrance supply

The S2 has a similar but more refined look than its S1 predecessor. The subtle bronze tint to sections of the robot and docking station give it a premium aesthetic that blends nicely with the futuristic lighting in both the clean water tank of the dock, and the robot’s onboard dust bin.

Taller than many docking stations, but significantly more elegant than most, the Omni S2’s appearance helps to justify its lofty price tag — and that’s further aided by the display and touch controls on top of the dock. These are handily located to press without stooping down to the robot itself, while the screen is useful for checking on the robot’s status and spotting error messages.

Short of making you a cup of tea while the robot cleans up, the S2’s docking station does absolutely everything. It charges the robot, empties its dust bin, replenishes its water supply (and even ozonates fresh water before it’s fed to the mop), cleans the mop with water heated to 70 degrees centigrade, dries it with hot air, refills the detergent tank, and has enough dust bin capacity for up to a claimed 68 days between bag replacements.

The robot itself is almost circular, with a central roller that’s claimed to be 100 percent tangle free, a pair of spinning side brushes, and a roller mop that self-cleans, slides outwards by 1.5cm to reach into corners and even an onboard fragrance supply to make your home smell nice. The S2 includes three different fragrances in the box, but these are a bespoke design so replacements can only be bought from Eufy itself. The same goes for the detergent bottle too, while thankfully the 2.5-litre dust bags are generic.

I like how the Omni S2 looks. Its design is more sophisticated than that of the S1, and I can imagine it neatly complementing the lavish houses of its deep-pocketed buyers. And while tall, at 670mm (26.4 inches), the docking station is relatively slim.

The robot is also relatively short, at 85mm. This compares favorably against taller, bulkier robovacs like the Dyson Spot+Scrub AI, which towers over the Eufy at 110mm and is less capable of cleaning beneath low furniture.

A welcome design upgrade for the Eufy Omni S2 is its ability to now clear door thresholds up to 4.2cm tall, up from just 2cm for the Omni S1. I was often left frustrated by that robot’s inability to drive up from exposed floorboards to a carpeted neighboring room, but have had no such issues with the S2.

• Design score: 5/5

Eufy Omni S2: performance

• Impressive vacuuming
• Excellent mopping
• Strong improvement over the S1

From the setup process and mapping, to vacuuming, mopping, navigation and self-cleaning, the Omni S2 is a triumph. You might say it should well be for the massive price tag, but even in 2026 it’s rare for such a complex new product to impress so universally. Where the Eufy Omni S1 struggled in some key areas — navigation, threshold clearance and sometimes even vacuuming — the S2’s performance is close to perfect.

Yes, it’s an ultra-premium product with a price to match. This is right up there with your Leica camera, Rimowa suitcase and five-figure turntable. I imagine the typical Omni S2 owner is the sort of person who wouldn't blink at splashing out on a pair of Apple AirPods Max 2 at the airport because they forgot their first-gens at home. They’d probably deal with a flight delay by picking up a new Swiss watch, too.

And that’s absolutely fine. Whatever the product, there’s always something that happens to sell the most expensive one, and for robotic vacuums that just so happens to be Eufy with the Omni S2. That doesn’t inherently count against it, because there are always customers happy to pay a premium for the one they like, or not really care about the cost because the S2’s spec sheet, design and feature set already put it at the top of the market.

What matters is how it performs in the real world, and how that compares to user expectations. Naturally, mine were at an all-time high and the S2 mostly delivered. The vacuuming performance is noticeably better than with the S1, and after a month of testing I still smile at the neat stripes vacuumed into my lounge carpet — and at how pleasant the S2’s fragrance system makes every room smell.

Eufy has improved navigation since the S1, and now the S2 is smart enough to not vacuum over the tasselled ends of a rug. It also automatically detects rug and carpet thickness, then raises itself by up to 50mm (1.97 inches) to prevent getting stuck in deep-pile fabric. In my testing, the S2 flagged a potentially tricky bit of carpet — which was actually an integrated but deeply contoured door mat — so I could tell it to ignore the concern or permanently avoid it.

Navigation and map creation is generally good. The robot only once got stuck and called for help, and I was impressed by how quickly the S2 mapped the ground floor of my home and did a decent job of detecting room boundaries. I used the app to fine-tune these, and was pleased to see how the S2 had added 3D cupboards, sofas, tables, chairs and other bits of furniture to the map. This isn’t strictly necessary, but it’s nice to see how the S2 correctly understands its environment.

Eufy claims a maximum suction of 30,000Pa, which is a huge upgrade over the 8,000Pa of the Omni S1 and other Eufy robots like the X10. There are four suction modes — Quiet, Standard, Turbo and Max — three options of cleaning intensity, three water levels, and the option of performing each cleaning task once or twice. As with the S1, the S2 returns to base whenever it needs to empty its bin, clean the mop, replenish its water supply or charge the battery. A mode called AI Automation promises to adjust cleaning strategy based on room type, floor material and cleaning frequency.

The Omni S2 deeply impressed during the first few weeks of general use, keeping hard floors and carpets clean — even after a cockapoo puppy joined our household, and his insistence on helping with garden projects brought a lot of dirt into the house. It was a joy, quite frankly, to have the S2 on hand, ready to clean up after every chaotic evening of dog zoomies.

I also loved how the S2 kept itself clean. Not only is the mop cleaned and dried with every use, but the cyclone-style dust collection ensures the onboard bin is practically spotless after each empty, and the filters don’t get clogged up. The rollers also looked like new after many hours of use, thanks to an anti-tangle design that actually works.

The mopping system works as well as the S1’s — evidenced by the absolutely filthy water collected in the waste tank of the docking station. I’d recommend owners empty this frequently, because if you wait a couple of weeks or so until it’s full, pouring it away is a seriously stinky process.

During TechRadar’s standardized robovac tests the Omni S2 continued to perform very well. These tests include two rounds of vacuuming on both carpets and hard floors, plus an obstacle avoidance test and a mopping test.

Pleasingly, the Omni S2’s vacuum performance is better than its predecessor, the two-year-old Omni S1. Vacuuming up oats from carpet was particularly impressive, with not a single piece being missed (except where I set the target zone in slightly the wrong place).

Before vacuuming

After vacuuming

During these tests I found the quickest, least powerful mode, called Quiet, was indeed very quiet (just 55 decibels on carpet), but the S2 performs best when suction is upped to the Standard or Turbo modes, cleaning intensity is increased from Fast to Standard, and the S2 is asked to perform two passes of the target zone or room, instead of one.

A crumb mix made of flour and crushed biscuit was completely lifted from a wooden kitchen floor using the S2’s standard intensity and suction settings, while on carpet I found Turbo or Cyclone (the most powerful suction mode) was best.

Crumb mix before first pass

Crumb mix after first pass

With that enabled, plus the intensity increased to Deep and the number of passes upped to two, the robot did a superb job.

Crumb mix after first pass

Crumb mix after second pass

The oat test is usually tougher, because robovacs tend to flick larger debris across hard floors with their spinning side brushes. The Omni S2 fell foul of this too, but as ever my advice is to set the robot to vacuum the entire room twice, instead of aiming for a target and kicking it everywhere.

With the right settings applied, the S2 picked up every single piece – and passed the same test with flying colors on carpet too, where flicking debris is less of an issue.

Before vacuuming

After vacuuming

I tested the mopping system with a dried smear of ketchup, which was promptly removed from the wooden floor. The cylindrical mop spins and pivots outwards to reach into the edges of the room, while the robot scrapes it clean and washes it while driving. The mop is then dried with hot air at the base station, which takes several hours but is very quiet.

Before mopping

After mopping

Meanwhile, the S2’s obstacle avoidance saw it drive neatly around a shoe, a sock and a USB cable strewn across the floor. I was impressed by how close it got to each, with moving or ingesting anything.

Overall, the Eufy Omni S2 performed brilliantly. I would recommend using Standard intensity and Standard suction with two passes most of the time, then up the suction to Turbo or Cyclone for a deeper clean. The latter hitting just 70 decibels was also impressive — for context, my Dyson V10 stick vacuum is 90 dB at medium power.

I only encountered one serious problem with the S2, and unfortunately it led to a replacement unit being provided by Eufy. The first S2 performed perfectly for a month, but developed a fault where the robot and docking station lost their connection. Several reboots and lots of advice from customer services failed to find a solution, so a second S2 was delivered and the original went back to Eufy for an inspection.

Naturally, this is disappointing for such an expensive product. But I was impressed by Eufy’s customer service department — which I approached as a customer and not a journalist — and how quickly the problem was resolved. The second unit performed perfectly throughout the rest of my test.

• Performance score: 4.5/5

Eufy Omni S2: app

• Easy to use
• Lots of configurability
• Also handles Eufy security products
• Option to charge at night — great if you have an EV tariff

The Eufy app gets better with every revision, and today it’s one of the best robovac apps I’ve ever used. Everything is logically laid out, with just the right amount of adjustability on offer to keep both newcomers and power users happy. The app is quick, responsive and presents everything in a way that’s easy to understand.

I especially like how it adds virtual furniture to your floor maps, which makes it easier to understand the layout and visualize where the robot is. Editing floor plans also works well, with simple tools for splitting, combining and renaming rooms after the robot has created an initial (but not always accurate) map of your home. Multiple floormaps can also be created, making it easy to save a second map for your bedrooms upstairs, for example.

Another feature I like is how pre-defined tasks can be created. I have one called “After dinner”, which tells the S2 to vacuum and mop my kitchen a certain way. A single tap of this from the Eufy app home screen, and the robot gets to work.

Since getting a puppy I’ve come to value Eufy’s child lock function, which disables the buttons on top of the robot – handy for both inquisitive children and dogs alike. I also like the off-peak charging function, where you can configure the S2 to only charge its battery at certain times of day. Since I have an electric car and an EV tariff, I’ve set the robovac to only charge at night, when my electricity is much cheaper.

• App score: 4.5/5

Should you buy the Eufy Omni S2?

Buy it if

Don't buy it if

How I tested the Eufy Omni S2

I lived with the Eufy Omni S2 for several weeks before writing this review. During that time it was used exclusively to vacuum the carpets and mop the floors of my house. I tested its cleaning abilities, tried some of the included fragrance diffusers, and noted how its self-cleaning systems fared after many hours of use.

I then carried out a number of specific tests to understand how well it cleans different types of debris from carpet and hard floors, how effective its mopping system is, how good it is at avoiding obstacles, and how loud it is.

First reviewed July 2026

Dimplex FlexBlade Multi-Directional Bladeless Fan: two minute review

The Dimplex FlexBlade isn't your traditional tower fan, although you can use it as one. It's bladeless, Dyson-style, so it delivers smooth airflow without the buffeting of a bladed fan.

The design is very flexible, enabling you to use it as a T-shaped floor fan, a vertical pedestal fan, or any angle in between. Air comes out of two wide vents, and those vents can be rotated 90 degrees in either direction so that you can have wider airflow or cool two areas simultaneously. That could be useful in shared spaces such as offices, although as the fan's stand isn't telescopic, one of you will get a cool back while the other gets cool legs.

The FlexBlade looks like it'll be extremely powerful but the strength of airflow drops off quickly with distance, so at full power with both blades pointing forward it felt like a breeze at three meters. It's fairly quiet, though, and delivers similar airflow and noise levels to our trusty Dyson Hot+Cool fan.

This isn't the most powerful floor fan we've tested by any means but it does move a decent amount of air and that flexible design makes it useful for multiple applications, such as the bedroom at night and home office or living room during the day.

Dimplex FlexBlade fan review: price and availability

• Launched June 2026
• UK only
• £199.99 (about $160 / AU$230)

With fortunate timing, the FlexBlade launched during a month of record-breaking heat in the UK. The Dimplex FlexBlade Multi-Directional Bladeless Fan launched in the UK in June 2026 with a recommended retail price of £199.99 (about $160 / AU$230). It isn't currently available in Australia, and Dimplex doesn't sell its home cooling products in the US.

I'm writing this as more really hot weather is toasting the UK, so I need to temper my usual buying advice with the fact that for many people the only criteria for a fan right now are 'will it cool me down?' and 'is it in stock?', to which the answers are yes and at the time of writing, yes. But I would point out that Dimplex dropped the price to just £123 for Amazon Prime Day 2026, so if you're not reading this in sweltering temperatures you can expect similar discounts in the cooler months when demand sags.

Value for money: 4/5

Dimplex FlexBlade fan review: design

• Horizontal and vertical adjustment
• Horizontal oscillation
• Simple but effective controls

I can't talk about the design of the Dimplex FlexBlade without addressing the elephant in the room, or rather the Shark: the Shark TurboBlade cooling fan, which seems to have inspired Dimplex's designers. Both have a propeller-esque T-shaped design with two independent, rotatable bladeless vents. Both can pivot from horizontal to vertical mode. Both project air up to 20 meters. Both have a magnetic remote control. Both have a quiet sleep mode. And both have multiple speed settings: 10 for the Shark and five for the Dimplex. I think the Shark is a little nicer looking, more flexible thanks to its telescopic pole and less top-heavy — the Dimplex wobbles a bit when you touch it — but it's also £50 (about $70 / AU$100) more expensive when it's not in the sales.

The FlexBlade arrives in six parts: the main motor unit, a two-part riser with a heavy base, and the two vents. It's simple and quick to put together – the only tool required is the provided Allen key for securing the base — and the remote attaches magnetically to the top of the unit so it's always handy.

Controls are kept to a minimum on the fan itself: power/speed, oscillation and timer. The remote is simple too, with the addition of dedicated speed up/down buttons, a full speed button and a sleep mode button to put the fan into its lowest power state overnight.

The T-shaped, two-vent design delivers a lot of flexibility. You can't adjust the 1.1m height of the main motor unit but you can position the two blades vertically, horizontally or in between, and you can rotate them independently up to 180 degrees to push air in two opposite directions at once. The rotating blades are a little stiff but not awkwardly so. The blade adjustments are manual but the fan itself can oscillate automatically, delivering horizontal oscillation of 30, 60 or 90 degrees.

Design: 4/5

Dimplex FlexBlade fan review: performance

• Oscillation and adjustable vents
• Quieter than similar rivals
• Best experienced reasonably close

The Dimplex promises airflow in excess of 6m/s with a 20-meter range and 90-degree sweep, but at full power with both blades pointed directly at me from three meters away it felt like a very mild breeze. At that distance and with the blades arranged vertically the remote control was very hit and miss.

The Dimplex is a bit quieter than the Shark – Dimplex's figures say it's 36dB at its lowest setting and 58dB at full pelt, compared to the Shark's 40dB to 66dB – but it still gets loud at higher fan speeds with the telltale whoosh we've come to expect from bladeless fans. It's not Dyson hand dryer loud at full power, though; it's more like a hair dryer on a very low setting.

I compared the Dimplex's airflow to two other room fans: a Dyson Pure Hot + Cool and a Meaco Sefte 10-inch air circulator. Both the Dimplex and the Dyson are bladeless and moved air a similar distance with similar noise levels, although the Dyson's wider diffusion mode made its output quieter at the expense of focused air. But the Meaco was quieter than both and delivered significantly stronger airflow across a large living room.

Performance: 3/5

Dimplex FlexBlade fan review: should you buy it?

Buy it if...

Don't buy it if...

Dimplex FlexBlade fan review: also consider

Dimplex FlexBlade fan review: how we tested

I tested the FlexBlade for a week at my home in Scotland during July 2026's UK heatwave. Scotland escaped the worst, because while England boiled the temperatures here were milder, peaking at 27ºC / 80.6ºF. That's hot enough to need a powerful fan but not so hot that I was crawling into my freezer or taking cold showers fully clothed.

I work from home in a long downstairs room that gets sunshine from both directions during the day, and that means it's often warmer inside than out – especially in the evening, as UK homes are typically made to retain heat rather than reflect it. I tested the FlexBlade as a daytime fan in my living room/office and as a bedroom fan overnight to see if it could keep me cool during the day, cool my family in the evening and help me sleep better at night.

First tested July 2026

Laifen T1 Pro: two-minute review

On first impressions, the Laifen T1 Pro wows. Open the box and you're greeted with Apple-inspired packaging, while the shaver itself immediately looks the part. Its CNC-machined unibody aluminium body looks and feels genuinely premium and, if you're used to cheaper shavers like the Philips OneBlade – my usual razor – it's impossible not to grin at the magnetically attached shaving head, which somehow manages to feel genuinely futuristic.

Modern conveniences like USB-C charging, an aeroplane mode to stop the power button being pressed in your bag while travelling and IPX7 waterproofing all add to the premium feel. Based on the spec sheet and those first impressions, you'd be forgiven for thinking the Laifen T1 Pro was one of the best electric shavers on the market.

The problem is that, with a shaver, the only thing that really matters is the shave itself, and that's where the Laifen T1 Po disappoints. I shave twice a week and have fairly coarse stubble, and despite repeated attempts the T1 Pro simply couldn't deliver a comfortable shave and often snagged on my hairs, which was painful and left me with patchy stubble. You have to limit your expectations a bit with single-blade razors, but I've been getting an effective shave with my Philips OneBlade for years, and often I found myself reaching for it to finish up and get the hairs that survived the T1 Pro's efforts.

This leaves the Laifen T1 Pro in an awkward position. It's beautifully designed and genuinely pleasant to use in every respect until it comes to shaving, but if I have to reach for a second razor to finish the job, the premium build and thoughtful features become little more than a nice distraction. I'd love to see Laifen revisit the shaving head in a future model because the engineering elsewhere is genuinely impressive, but as it stands I can't recommend the T1 Pro.

Laifen T1 Pro: price and availability

• List price: $149 / £149 / AU$246
• Launched: September 2025

The Laifen T1 Pro launched in September 2025. Listing prices vary but are consistent with other premium shavers. In the US it's currently selling for around $129, in the UK it's £149 and in Australia it's $239. However, it doesn't come with a case, cleaning materials or anything else so it may feel steep in comparison

• Value score: 2/5

Laifen T1 Pro: design

• CNC-machined aluminum feels premium
• Magnetic head feels futuristic and makes cleaning a breeze
• USB-C means you're just taking one cable away with you

The Laifen T1 Pro makes an excellent first impression. Unlike the plastic-bodied shavers that dominate the market, the T1 Pro is built around a CNC-machined unibody aluminium chassis that immediately feels more like a premium gadget than a bathroom appliance. The fit and finish are excellent, while the magnetically-attached shaving head snaps satisfyingly into place and makes cleaning refreshingly simple.

Laifen has also packed in plenty of thoughtful features. USB-C charging means one less proprietary cable to keep track of, an airplane mode prevents the power button from being accidentally pressed in your luggage, and the IPX7 waterproof rating means you can use the shaver wet or dry before simply rinsing it under the tap to clean it up.

The compact dimensions work in the T1 Pro's favour. It's comfortable to hold despite the lack of any rubberized grip, and the aluminum body never felt slippery during my testing, even during a heatwave when I was, perhaps a little sweatier than I'd like to admit. Its low weight, just 3.3oz / 93g, makes it easy to use precise movements in the tricky areas like the jawline and around the mouth — areas that can be difficult with larger, clunkier, shavers.

It's a minor thing, but I found myself squeaking with joy each time I opened the little cap at the bottom of the razor to reveal the USB-C charging port. It's a small thing, but the cap fits so neatly in and comes away so delicately it sparks joy every time I charged it.

In many ways, the T1 Pro feels like the product of a company obsessed with industrial design. From the premium materials to the magnetic shaving head and clean, minimalist aesthetic, there's very little to criticize about the hardware itself.

• Design score: 4/5

Laifen T1 Pro: performance

• Foil snags on coarse hair, which is painful
• The shave is patchy and inconsistent
• Long-lasting battery means you'll only need to charge occasionally

Ultimately, the Laifen T1 Pro lives or dies by the quality of its shave, and that's where it struggles. I have fairly coarse facial hair and typically shave twice a week, which proved to be a challenge the T1 Pro never really overcame.

Rather than cutting cleanly through my stubble, the shaver frequently pulled at beard hairs, making each shave less comfortable than it should have been. It also struggled to achieve an even finish. Even after several passes, I was often left with patches of missed stubble that required further attention. The trimmer head was more prone to this snagging, but the shaver head didn't eliminate the problem and also left my skin irritated.

The T1 Pro's light weight makes it easier to use, but its small size means covering your face takes longer than with a larger foil shaver. As a result, multiple passes quickly became the norm, and each additional pass increased the likelihood of the shaver snagging on thicker patches of hair.

I repeatedly found myself reaching for another razor to finish the job. Not only did it clean up the areas the T1 Pro had missed, but it also did so more comfortably. That's difficult to overlook given the T1 Pro's premium price.

The 120-minute battery life is excellent and should last most people several weeks between charges.

Unfortunately, The Laifen T1 Pro looks and feels like a premium electric shaver, but in my experience it simply doesn't deliver the shave the design promises, which makes it impossible to travel with because I also have to toss a second razor into my bag.

• Performance score: 1/5

Should you buy the Laifen T1 Pro?

Buy it if

Don't buy it if

Laifen T1 Pro: also consider

First reviewed July 2026

When I wrote my Ninja Creami Swirl review, I decided that the main reason that anyone should consider buying a Ninja Creami machine is so that they could make frozen treats that match their health goals. Whether you are trying to avoid processed foods, cut calories, reduce sugar, avoid dairy, or cater to any other specific dietary needs, any Ninja Creami model can make you a healthier version of ice cream or sorbet. I've tried tons of recipes, and here I'm sharing the ones I like best, specifically without artificial sweeteners. You can alter any recipe to best suit your own preferences.

Just fruit

Canned fruit makes the easiest possible sorbet. Just open a can of your favorite fruit, pour it in, freeze for 24 hours, and spin it on the Sorbet cycle. Canned fruit is so soft that there's no need to blend before freezing. I used a can of mangoes in 100% juice here. If you want more protein, you could add some yogurt or milk of your choice; I suggest a 2:1 fruit to dairy ratio.

I had a ton of watermelon left over from a recent party, so I threw some into the Ninja Creami container. Again, watermelon is a soft fruit so I didn't blend it first, but I did squash it down a bit to release some of the liquid so it would freeze as a solid block. The resulting sorbet had a lovely texture, but it really wasn't sweet enough for my palate so I'd recommend adding some honey before freezing. You could also add milk for some protein, or coconut water for extra electrolytes.

Banana date nut (or chocolate) ice cream

Here is the recipe I used, but there are many alterations you could make here. If you don't want nuts at all, you could use cacao powder instead of nut butter for a chocolate flavor. Or use both for a chocolate-nut option.

1/2 cup plain Greek (or vanilla) yogurt

2/3 cup water (or use milk for more protein)

2 tbsp nut butter (I use PB2 powder but any works)

1/2 large banana (or 2/3 small)

4-6 dates to taste (can skip if using flavored yogurt)

(optional) 1 tbsp hemp seeds

(optional) 1 scoop unflavored collagen powder

After blending and freezing for 24 hours, process this on the Frozen Yogurt setting. I used the hemp seeds and collagen for their health benefits, and they don't have an effect on the taste. You could skip those entirely if you like.

Pistachio ice cream

I think this is tasty, though a friend of mine remarked that while it had the texture and mouthfeel of ice cream, it "tastes healthy". Do with that what you will.

1/2 cup cottage cheese (I used 2%)

1/4 cup yogurt (I used plain nonfat Greek)

1/2 cup pistachios (I used salted but rinsed them off)

1/2 cup milk (I used almond)

4-8 dates (I used 8 small)

1/4 tsp almond extract

Honey/maple syrup/agave syrup to taste if needed (I used about 1/2 tbsp agave)

If you use unsalted nuts you’ll want to add a pinch of salt. You do need to blend this well before freezing. Taste it before you freeze it to see if you need to add honey or syrup. You want it to be slightly sweeter than you think you need, because frozen food tastes less sweet.

Process this on the Frozen Yogurt cycle. If you like, add more nuts and/or chocolate chips in the Mix-In cycle.

Açai bowl

One serving frozen açaí cubes or packet

1/2 banana

Handful berries

Juice or milk to fill line (if milk you’ll want to add a little honey for sweetness)

Blend, then freeze for 24 hours and spin on the Sorbet setting. Top with berries, seeds, nuts, granola, coconut, nut butter, cacao nibs, or whatever you like. I enjoyed mine with chia pudding, pumpkin seeds, and granola.

Real ice cream

If by healthy you mean wholesome, with no fake anything, just real ingredients, then this is the way. Credit goes to the New York Times. It's a plain base, but by adding vanilla (or any flavor) extract, cacao powder, fruit, or just about anything, including Mix-Ins, you can make any flavor you can imagine. While it's obviously not low in calories, fat, or sugar, it doesn't have any unpronounceable junk in it. It's absolutely delicious and rivals anything you can buy, anywhere.

Here is the basic recipe:

2 cups heavy cream

1 cup whole milk

2/3 cup granulated sugar

1/8 tsp fine sea salt

6 large egg yolks

In a small pot, simmer the cream, milk, sugar, and salt until the sugar dissolves, about five minutes. Remove from heat.

In a separate bowl, whisk the yolks. Whisking constantly, slowly whisk about a third of the hot cream into the yolks.

Whisk the yolk mixture back into the pot with the cream. Return pot to medium-low heat and gently cook until the mixture is thick enough to coat the back of a spoon (about 170 degrees.) Strain through a fine-mesh sieve.

Pour mixture into the Creami containers no higher than the fill line; this will be enough for two containers. Freeze for 24 hours and process on the regular Ice Cream setting.

Don't be afraid to experiment

It's worth noting that the Ninja Creami is sort of magic in the sense that it creates a lovely texture, almost regardless of what you put into it. However, it doesn't magically change the flavor, as people often hope. If you don't particularly like what you're putting in (a protein shake, for example) hoping that it will taste better after the Ninja Creami treatment, well, you'll be disappointed. You get out what you put in.

The Ninja Creami lends itself to experimentation. Even following someone else's tried and true recipe doesn't guarantee you'll like the results. But keep trying, you'll find the recipes that suit your tastes and health preferences.

• Universal fit with cooling, improved coverage and better battery life
• On sale from 29 July 2026, pre-orders open now
• It's £339.99 (about $459 / AU$655)

We really rate the Shark CryoGlow LED face mask, giving it four and a half stars out of five in our Shark CryoGlow review. Our only real niggle was the relatively short battery life, so we're pleased to see a newer version with more stamina and even better facial coverage. Say hello to the Shark CryoGlow Plus, which promises to deliver everything we liked about the original with some important improvements.

As before, the CryoGlow Plus uses three kinds of LED light: blue, red and deep infra-red. Coverage has been improved 120% around the crows' feet area in this new model and it's more energy efficient too.

Shark CryoGlow Pro: key features and price

The CryoGlow Plus has Shark's InstaChill Cold technology, which provides two active cooling points to help soothe the under-eye area. The mask's Under-Eye Revive Mode has three cooling levels and you can use it solo or alongside any of the LED modes.

There are three LED modes: Better Ageing Mode, which is a six-minute treatment using red and deep infra-red light; Blemish Repair Mode, which is an eight-minute, three-phase routine using blue and deep infra-red before finishing with red LED light; and Skin Sustain Mode, which is a four-minute maintenance treatment using red, blue and deep infra-red.

In our time with the original CryoGlow we were impressed by its performance, with the important caveat that your mileage may vary because everybody's skin is different. We particularly liked the InstaChill feature, which really did de-puff the under-eye area. Provided you keep up your use of the mask, we found it to be the best alternative to regular, professional skincare treatment.

The CryoGlow Plus is only marginally more expensive than its predecessor: that had a list price of $349 / £299 / AU$699, while the CryoGlow Plus is £339 in the UK. US and Australian prices haven't been announced yet but that's about $459 / AU$655 before taxes and tariffs.

The CryoGlow Plus officially launches on 29 July but you can pre-order from SharkNinja.co.uk and John Lewis now. It'll be available in two shades, Pastel Berry and Pastel Dusk.

• The Ninja Crispi Microwave helps avoid the problem of soggy reheated food
• It has a huge array of presets to easily handle common cooking tasks
• It's on sale in the US; international launch details are yet to be announced

Although they're fast and convenient, microwaves tend to make food soggy. That's where Ninja's new Crispi Microwave comes in, combining the fast heating of a microwave with the crisping effect of an air fryer.

Ninja's new release isn't the first combined microwave and air fryer on the market; brands including Samsung, Smeg, and even IKEA have all released their own two-in-one appliances that can defrost, cook, and crisp meals and leftovers.

There are two key things that set the Ninja Crispi Microwave apart, the first of which is its huge range of handy presets for common kitchen tasks. Not only does it come with the usual settings you'd expect for jobs like heating frozen dinners and bringing leftover pizza back to life, it also has dedicated modes for preparing soup, making popcorn, and even softening butter, taking the guesswork out of simple kitchen tasks that would usually require careful monitoring to ensure nothing melts or burns.

The second unique selling point is its use of non-toxic glass for air frying. The Ninja Crispi and Ninja Crispi Pro air fryers cook food inside resealable glass containers rather than a drawer, giving peace of mind if you're worried about non-stick coatings. The Crispi Microwave contains a deep dish made from the same glass, which has a capacity of 5.5 quarts / 5.2 liters. According to Ninja, that's big enough to hold an 8lb chicken, or four slices of pizza.

When you've finished cooking, both the dish and crisper plate are dishwasher-safe, and with no rotating plate, the interior of the microwave is easy to wipe clean.

The Ninja Crispi Microwave is available now direct from Ninja for $449 (about £330 / AU$640) in the US. International release dates and prices are yet to be announced, but we're hoping to test it soon to see whether it can earn a place in our full roundup of the best air fryers.

When temperatures start to rise, a great fan is essential to help you feel cooler. Where I live in the UK, we're now on our 45th heatwave of the year (an exaggeration, but it doesn't feel like it), and I'm basically never without a fan these days. I carry one about the house with me wherever I go, and I have one on throughout the night too. I've even bought one for the dog, although he's still quite suspicious of it.

At TechRadar, we've tested dozens of different models over the years. We have a best fan guide that includes just a select group of our favorites, but there are plenty more excellent fans we've tried out and which are still worthy of your consideration. Below, I've rounded up our best-rated models. These are all the fans that scored four or more stars in our review (and are still in production).

For easy browsing, I've split the guide into three broad categories — desktop and handheld fans, pedestal fans, and tower fans — and included a quick overview of each kind to help you decide if it's what you're looking for. Hit the 'More details' button to find out more about what we thought of each individual fan, and a link to read the full review. Stay cool out there.

Desktop & handheld fans

Want to blast air at one specific target? You need a desktop or handheld fan. The latter is designed for personal use, on the go. There are plenty of cheap options cluttering up the market (and landfill sites), but this year we've also been treated to a couple of high-quality, long-lasting options from two of the biggest brands in the cooling business — Shark and Dyson. We loved both of them on test.

A desktop fan is essentially a pedestal fan without its pedestal. It's designed to sit on a surface — like a desk — and offer localized cooling. I also use one of these to cool my dog by popping it on the floor and facing it at his bed. Some can oscillate widely for more general cooling, but if you're looking to tackle a whole room, you might be better off with a pedestal or tower fan.

Pedestal fans

A pedestal fan consists of a fan head on a tall, skinny pole. They sit on the floor and can generally be fixed at a specific target or set to oscillate to cool a wider area. They're more portable than a tower fan, and some have telescopic poles or swappable bases to enable them to be set at different heights.

Tower fans

Tower fans can differ in appearance, but the term can generally be applied to a fan where the head makes up most of the bulk of the build (as opposed to the lollipop shape of a pedestal fan). They're generally not that easy to move about, and are designed for cooling a whole room at once. They're also more likely to have advanced smart features, or added functions like purification.

Philips Hue is widely known as the best smart bulb brand, but if you're looking to get yourself kitted out with a full Hue setup from the main range, it'll cost you. You might have spotted the brand's Essential range — which looks very similar to the main lineup but comes in at a much more affordable price — and wondered where the compromise is. You can see an Essential bulb on the left of the image above, next to a main range bulb on the right.

This article is here to help you figure out whether the Philips Hue Essential range is right for you, or whether it's better to splurge on the original lineup. We've tested both, and you can get the full low-down on what we thought of the budget-friendly bulbs in our Philips Hue Essential series review. For a quick summary, though — plus links to buy — read on.

Philips Hue Essential bulbs: reasons to buy

Let's start with the good bits about the Philips Hue Essentials range. Here are the main benefits to know about:

✅ The performance is excellent: In her side-by-side tests with the main range, our Homes Editor Cat Ellis found "both were equally responsive, and produced colors that were identical to my naked eye when [she] switched between scenes". The Essential bulbs are based on a different color-matching technology to regular Hue lights, but Cat "had a hard time telling the difference".

✅ They're compatible with the full Hue ecosystem: The Essential bulbs will play nicely with any Hue gadgets you already have, making them a great way to extend your existing smart light setup.

✅ They're much cheaper than the main range: While prices vary depending on exactly which bulb you're buying, generally the Essential models come in around half the price of the main range.

Philips Hue Essential bulbs: reasons to avoid

So what about the downsides? These are the main compromises you'll be making if you opt for an Essential bulb:

❌ The white shades don't match the main range: Essential bulbs have a narrower white light range, which is an issue if you were hoping to add them into a room that already has bulbs from the main lineup.

❌ They can't dim as low: Essential bulbs can only dim to 2%, whereas the main range can go right down to 0.2%. If you want seriously muted lighting, you'll need to shell out a bit more and stick to the main range.

❌ They can't get as bright: Essential bulbs have a lower maximum brightness capacity — they can reach 803 lumens, whereas some of the standard White & Color Ambiance bulbs can hit 1,600 lumens. It's worth nothing that this spec varies by bulb; not all standard bulbs have a higher max brightness than their Essential counterpart.

Philips Hue Essential Starter kits

Most people getting started with a Philips Hue lighting setup will begin by purchasing a 'Starter kit', which bundles some bulbs, a Philips Hue Bridge, and occasionally a bonus Philips Hue accessory. A Bridge isn't essential, but it is a good idea if you want to maximize the potential of your bulbs. There are a few variations available, with different numbers and kinds of bulbs included; I've listed a selection here.

US starter kits

UK starter kits

Philips Hue Essential bulbs

If you already have a Bridge and are looking to extend your setup, or are planning on going without (basic bulb functions can be controlled via Bluetooth), you can buy individual or multipack bulbs. There's a massive range — I've just included a selection here.

Whichever bulb lineup you choose, you'll have to decide between Hue's three light types. White and color ambiance bulbs can emit any one of millions of RGB colors, including a wide range of different white tones. White bulbs emit a warm light at a set color temperature, and White ambiance bulbs can be set to any one of a massive range of cool to warm white lights.

US bulbs

UK bulbs

• The Rivelia Start is De'Longhi's smallest automatic coffee maker
• It has a menu of 10 coffee drinks, including cold brew
• It's on sale now in the UK for £599.99 (about $800 / AU$1,160)

De'Longhi makes some of the best espresso machines I've tested here at TechRadar, and as the owner of a small kitchen, its latest model has particularly piqued my interest. The De'Longhi Rivelia Start is the company's smallest fully automatic coffee maker.

The Rivelia Start is a successor to the 2024 De'Longhi Rivelia, which our tester Josephine Watson gave a full five stars thanks to its consistently well-extracted espresso, clever Bean Adapt technology that optimizes brew settings to suit your preferred beans, and LatteCrema Hot system, which creates thick and creamy foam for milky drinks.

The Rivelia Start offers all that in an even smaller package, and adds the ability to prepare authentic-tasting cold brew. De'Longhi promises that your cold brew will be "ready in under five minutes", which tells me that it's not just pouring a shot of hot coffee over ice, like some other machines I've tested recently. Instead, the coffee is extracted using ambient temperature water, which results in fewer bitter compounds being dissolved for a more mellow flavor.

The Rivelia Start's standard menu contains 10 drinks, but if you like the idea of an iced latte or cappuccino to help you stay cool in the summer months, you can upgrade your Rivelia Start with the optional LatteCrema Cool set, which lets you create chilled milk foam for six further drinks.

Personally, the feature I'm most excited about is the pair of swappable bean hoppers. My job sometimes involves drinking a lot of lattes, and I always prefer to switch to decaf in the afternoon so I can still sleep after a day testing drip and espresso machines. With the Rivelia Start, there's no need to purge one type of coffee from the hopper before refilling with another; just unscrew the whole thing and swap it for one filled with a different type of bean.

It's simple to operate too, with an interface of clearly-labelled buttons rather than a touchscreen, making it extra accessible for new users.

Its small size isn't the only thing that sets it apart from other coffee makers, either — it also comes in a palette of earthy colors that fit with the current trend for natural shades and textures, which makes a refreshing change from the stark black, white, and chrome that once dominated kitchen appliances.

It's available to buy now direct from De'Longhi in the UK for £599.99 (about $800 / AU$1,160) in two colors: maple brown and jade green. More hues will be available from third-party stores from September, and we're currently waiting for details of its international launch.

Ninja makes some of the best air fryers on the market, but considering how easy these appliances are to use, it sure is difficult to figure out which one to buy. This brand's air fryer range has grown to incorporate dozens of models with different capacities and capabilities.

We've tested ... okay not all, but a decent number of them, so we're in an ideal position to help. The good news is they almost always score highly in our tests, which means you're unlikely to come away disappointed, whichever one you go for.

However, some models will be better suited to your needs than others. Below, I've rounded up all the Ninja air fryers that we've tested and recommend, and which are still available — and if you hit the 'View details' button you can see exactly what we thought of each one. Skip to the bottom of the page for some top tips on how to choose the right one for your kitchen.

Let's fry, let's fry away

How do I choose?

If you're feeding larger numbers or want to create multi-component meals (and have enough counter space), look at the Foodi Dual Zone options — these feature-packed air fryers have two drawers that can be set to different temperatures, and the machine will sync up cooking for you so the food in both sections is ready at the same time. Or, for the same functionality but a smaller footprint, you can't beat the Double Stack, which puts one drawer on top of the other (there are a few capacities available).

Those with small kitchens should consider a Crispi model. These have an innovative design that's essentially a glass container onto which an air fryer hat attaches. The containers can be used as serving or storage dishes, for maximum versatility.

If you don't just want an air fryer, plenty of Ninja's appliances double up as different kinds of cooker. One of the most versatile additions to the range is the French Door Air Fryer, which offers 10 cooking modes and can fit a whole roast or pizza inside. Alternatively, you have things like the 5-in-1 Grill & Air Fryer, which come with a range of accessories including a griddle plate for an authentic chargrilled finish.

If you're still feeling overwhelmed, I don't blame you. There's a lot of overlap between what these air fryers can do, so I'd start by looking at how much space you have on your counter, and how much capacity you need in your air fryer, and use those requirements to narrow your options down.

The Ninja Slushi is one of my all-time favorite kitchen appliances, but it's simply too large for my kitchen. Thankfully there are personal blenders that are smaller, cost a lot less, and make perfect slushies for one in just a few seconds — and here I've picked three of the best that can tackle ice and other frozen ingredients with ease.

Some single-serve blenders struggle to tackle any ingredients tougher than an apple, but each of the models here will crush ice effortlessly despite their compact size. Once you're done, you can take your drink on the road, to work — or just to the back yard for sipping in the sunshine.

Slushies made this way won't be identical to those created with a Slushi machine, but they can come close. The Slushi works by taking liquid ingredients and freezing them while stirring to create small ice crystals, whereas blenders create slush by chopping up large pieces of ice. If you want an undiluted slushie without added water, try freezing ingredients like juice or soda in an ice-cube tray. Provided you add the recommended amount of liquid to your blender's cup (usually around 6oz / 170ml) you should get a very similar (and equally tasty) result.

Ninja BlendBOSS

At 1,200 watts, the Ninja BlendBOSS has the most powerful motor of all the blenders in this list, and transforms ice and frozen fruit into slush with ease. It consists of a sturdy, unusually-shaped base (which reminds me of a UFO) and a Stanley-style cup, with a sip lid and straw that you can carry, or tuck into your car's cupholder.

It has three preset options (smoothie, ice crush, and blend) plus a pulse option so you can take control yourself. The preset programs will blend and pause in different patterns to ensure all the ingredients come into contact with the blades — and they're very effective. Our reviewer Karen Freeman reported that her smoothie with frozen berries "came out perfectly smooth [with] no chunks of blueberry skin or spinach" and the blender "turned ice into snow incredibly quickly and thoroughly" for iced lemonade. Your recipe needs to include at least 6oz / 175ml liquid along with the ice for proper blending.

Some single-serving blenders tend to jump across your kitchen counter when dialled up to full, but the BlendBOSS has a cleverly designed base with a circle of grippy silicone, plus suction cups to ensure it doesn't dance onto the floor when preparing iced drinks.

The only downside we found is that the lid of the chug cap sometimes fell down and bopped us on the nose mid-slurp, but that was only a very minor annoyance. This is otherwise a brilliant tool for making slushies and smoothies, and very reasonably priced too.

Read our full Ninja BlendBOSS review

Nutribullet Flip

Unlike the two other blenders here, which comprise a plug-in base that you keep in the kitchen and a detachable cup to take with you, the Nutribullet Flip is fully portable and rechargeable so you can whip up drinks on the move (particularly handy if you're at the gym and want a fresh protein shake, for example). Just add your ingredients to the cup, screw on the lid, flip it upside down and press the button. Thirty seconds later, you can turn it upright again and start sipping. What could be easier?

I was a bit apprehensive about drinking from the part of the blender that contains the motor, but you're in no danger at all of cutting yourself; the blade assembly is well away from the drinking spout and the motor can't activate unless the cover on the drinking spout is fully closed.

The Flip handles ice with ease, and I used it to prepare some very nice iced coffee drinks during testing. Particularly large frozen strawberries sometimes required a second blending cycle to be fully pulverized (the Flip only has one program) but nothing I tested could withstand a minute in contact with its blades. When you're done, the insulated cup keeps your slush and shakes cold for hours. You'll need to add at least 8oz / 235ml liquid along with your ice.

Something I particularly like about the Flip is that its blades are at the widest point of the cup, which means everything falls down onto them rather than getting stuck on the sides. It's especially easy to clean as well; add water and a drop of dish soap, run a cycle, then rinse.

Read our full Nutribullet Flip review

Ninja Blast Max

I awarded the Ninja Blast Max a full five stars thanks to its ability to turn even the toughest ingredients into a silky smoothie or tasty slush. Ice and frozen fruit were transformed into a frosty treat in no time at all, and tough fibrous vegetables like kale were no match for its powerful motor and super-sharp blades.

The Blast Max has a 'crush' setting specifically designed for ice, which turns rock-solid strawberries and raspberries into slushies in less than a minute. Alternatively, add plenty of ice, a shot of espresso, and a good splash of milk for a delicious iced coffee. Provided your drink includes at least 6oz / 175ml liquid, the Blast Max will handle it with ease. "The resulting blended iced coffee looked as good as anything you might get from a coffee shop, with a nice layer of foam on top and no chunks of unblended ice crystals," I said.

The Blast Max has a travel cup that detaches from the charging base for sipping on the move, with measuring lines clearly marked on the side. Ninja suggests that you might need to give it a little shake during blending to loosen any ingredients stuck to the sides that might miss the blades, but during my tests I never found that necessary.

The Blast Max is the most affordable of these three blenders right now, and no less impressive than the other two. For me, the only drawback was that, unlike the Nutribullet Flip, the Blast Max doesn't have an insulated cup to keep slushies frosty when you're on the go.

Read our full Ninja Blast Max review

• A software update bricked Philips Hue Bridge Pro devices
• The bug required a very specific set of circumstances
• Philips Hue has promised free replacements to affected users

Over the last few weeks, reports have emerged of Philips Hue Bridge Pro smart home devices becoming bricked, and it looks like the culprit has now been identified. According to Philips Hue, the fault lay with a recent software update — but the company has won plaudits for what it's giving to customers in order to make amends.

The trouble started in late June when Philips Hue released software update 2071353020, which was intended to include “several small changes” that improved the product’s operations. Yet reports started flooding in that the update had caused people’s Hue Bridge Pro devices to fail and become completely unresponsive.

In a statement to Ars Technica, Philips Hue explained the very specific circumstances that caused the problem: “The issue affects users who disabled automatic software updates, remained on an older software version for an extended period, and then manually installed a firmware update after the update package had been stored on the Bridge for more than 10 days.”

As well as that, the spokesperson noted that “Our data shows fewer than 100 Philips Hue Bridge Pro devices have been impacted.”

Still, any disruption like this is a pain. If you’re affected, not only will you have to wait for a replacement to arrive, but you’ll also have to reconfigure your lights and settings from scratch. That’s the kind of disturbance that is made all the more irritating due to the fact that it occurred after users updated their software — something that people are often encouraged to do in order to get the latest bug fixes and improvements.

Free replacements

While it’s always unpleasant to see a software update brick your device, Philips Hue has attracted praise for the way it’s responded. Not only has it issued a fix, but the company has promised that “We will replace affected Philips Hue Bridge Pro devices free of charge, regardless of warranty status.”

The decision has proved popular with Hue owners on Reddit, who've noted in one popular thread that it's a rare example of "big company actually making good". Another comment noted: “Considering the RAM prices too those Bridges went up in costs too. W to Philips on this one.”

If you haven’t updated your Philips Hue Bridge Pro for a while and think your device could be vulnerable according to Philips Hue's description, it might be worth getting in touch with the company first before attempting to update. The last thing you want is a bricked product on your hands.

And if you already have been affected, don’t spring for a replacement device just yet. You might be able to get a free replacement from Philips Hue, so be sure to explore that avenue first before spending a dime on anything new.

Dimplex Rechargeable Cordless Desk Fan: two minute review

Dimplex makes lots of floor, table and pedestal fans, and the Rechargeable Cordless Desk Fan is designed to address one of their weaknesses: they can only go where your plug sockets or extension cables can go. This affordable fan works as wired one via its USB-C port but also includes a rechargeable battery delivering up to 15 hours of air, or around four hours at full speed. That means you you can take it into the garden on a hot evening or take it to your bedroom and run it overnight.

The Dimplex Rechargeable Cordless Desk Fan doesn't oscillate but you can tilt it vertically up to 90 degrees, and it folds down almost flat so it's easy to keep in a drawer or toss into a bag. There are four speed settings here but the high speed one is not recommended while charging, as it depletes the battery faster than the USB-C connection charges it.

The fan works well and is fairly quiet, but it does make a noticeable drone at all speed settings; on a hot day, running the fan at high was very distracting. Of course all fans make some noise, but as this is a small fan with a 6.7 inch / 17cm diameter and 5.1 inch 13cm blades, you need to have it close to you to feel the benefit. In my home office the Dimplex on quiet setting at half a meter distance was noticeably louder than a much larger air circulator running at 50% speed one meter from me. If noise annoys, this may not be the fan for you.

Dimplex Rechargeable Cordless Desk Fan review: price and availability

• Launched July 2025
• UK only
• £34.99 (about $50 / AU$70)

The Dimplex Rechargeable Cordless Desk Fan, model DXRCFN, launched in the UK in July 2025. It has a recommended retail price of £34.99 (about $50 / AU$70), making it the most affordable model in the current range of Dimplex cooling fans and about £10 more expensive than a similarly sized wired desktop fan. It isn't currently available in Australia, and Dimplex doesn't sell its home cooling products in the US.

This fan has been cheaper – it was £25.45 during Prime Day 2026 – but I wouldn't expect to see any price cuts during the summer months in the UK.

Value for money: 4/5

Dimplex Rechargeable Cordless Desk Fan review: design

• Supremely portable
• Finger-friendly grille
• USB-C charging

The design of the fan is rather clever. It's been made for maximum portability, folding in on itself to resemble a small squashed football for travel or storage. It charges via USB-C and takes about four hours to charge fully. Because it's USB you can charge it with a phone charger or power bank, which makes it a good option for travelling. The battery is sealed inside and is not user-replaceable.

In addition to its internal bladed fan there's a circular louvred grille on the front that rotates and enhances the airflow. Although it spins quickly, the front grille is finger-friendly and won't hurt you or a child if you or they touch it (although you can lock it in place if you don't want it to spin).

The Dimplex fan doesn't oscillate, but you can adjust its vertical tilt by up to 90 degrees by moving the fan section up or down. It stays put without having to be screwed in place. Controls are simple, with just two buttons: power and speed. There's no remote control and no smartphone/smart home features.

Design: 4/5

Dimplex Rechargeable Cordless Desk Fan review: performance

• Decent airflow for its size
• Four speed settings
• Distracting sound

There are four fan speeds — quiet, low, medium and high — and I found that for my home office desk the quiet setting delivered a nice breeze without making me feel like I was in a wind tunnel. High speed was a bit intense up close but worked well from a little further away. Dimplex recommends only using High when you're on battery power as it can still deplete the battery when you're recharging it; at its lowest, quiet setting I managed 14+ hours from a single charge.

The Dimplex moves a decent amount of air for its size and it's fairly quiet in terms of its overall volume, which ranges from 36dB to 43dB. However, it does make a noticeable and constant droning sound that rises in pitch as you increase the speed. All bladed fans make some motor noise, of course, but desk fans are designed to sit very close to you, which means any noise is much more noticeable. For me it was too distracting at any speed when I sat it on my work desk, although in the bedroom at its lowest setting it didn't keep me awake.

Performance: 3/5

Dimplex Rechargeable Cordless Desk Fan review: should you buy it?

Buy it if...

Don't buy it if...

Dimplex Rechargeable Cordless Desk Fan review: also consider

Dimplex Rechargeable Cordless Desk Fan review: how we tested

I tested this Dimplex fan for a week during summery weather as both a desktop fan in my home office, and as a bedroom fan overnight. Both locations are in my house, where indoor temperatures were around 69.8°F to 75.2°F / 21ºC to 24ºC during the daytime and around 66.2°F to 68.0°F / 19ºC to 20ºC at night.

First tested July 2026

Need a fan to help you handle the ongoing heatwave, but found yourself facing empty shelves? Don't panic — there's still time to grab a great one, if you know where to look. I'm TechRadar's home tech expert, and I've scoured the web to find the fans that I'd buy with my own money, and which are still in stock for delivery this week.

First of all we have the Shark ChillPill, which I currently have in my bag, and is a lifesaver on public transport — or even if you're outside when the wind dies down and you're feeling uncomfortable. The fun colours are sold out, but it's still available in silver and grey. There's a Dyson Pure Hot+Cool HP00 still available to buy as well, and it will double as a heater when winter rolls around.

Dimplex's FlexBlade fan is still available, and blows a sheet of air over your bed. I used this fan when the temperature hit 35C and it was the only way I could get a proper night's sleep. I have a Meaco Sefte fan on my desk, and although Meaco's own storefront has been stripped bare, you can still grab its six-inch diameter air circulator at John Lewis if you're speedy. Read on for links to all these fans and more, but move fast — they won't be around for long.

Big-name fans still in stock

There's no mistaking the growing momentum behind small-scale, low-cost solar panel installations: panels you can plug into a standard wall outlet, without the expense, time, or paperwork of a full rooftop installation.

Now widely established in Europe (where the tech is best known as 'balcony solar'), we're starting to see a wave of American states move towards legalizing these plug-in panels as well. Utah was the first in 2025, and there are now proposals in 30 other states to make the devices available to buy.

They're perfect for renters as well as homeowners. You can take them with you if and when you move. Additionally, they offer some respite from the energy price crisis, and they're becoming increasingly widely available.

At the same time, we're seeing a record number of homes in the US installing battery energy systems, hooked up to rooftop solar or the grid — another way to reduce electricity costs and provide a backup for a creaking national power system. Here's what's happening with home energy tech right now, and where it's going next.

Plug-in solar: the state of play

Utah set the ball rolling for plug-in solar in the US by passing House Bill 340 in March 2025. It means that portable solar panels or rooftop panels — up to a total capacity of 1,200 watts (typically four roof panels) can be plugged into a regular outlet. These panel systems use an integrated microinverter to convert the panels' DC output into household AC, ready for use.

In the default setup, this means the energy produced by plugged-in 'balcony' panels will be taken up by your home appliances first, before they try to access the grid. While battery connectivity is possible, the general idea is that the energy isn't stored anywhere — it's just pushed into your home for use as needed.

Estimates suggest you can shave around 10% off your electricity bill, though this will vary a lot depending on factors like electricity prices and how much sunshine you get. You can think of it as a way of getting a sizable chunk off your bill, rather than something that's going to replace the power grid entirely. The kits themselves start at around $500 and go up from there.

Now other states are following Utah's lead. According to The Cool Down, more than 30 states have drafted some form of bill, while six states have already enacted related laws. You can keep track of what's happening via the Bright Saver tracker, which provides updates for each state and a handy interactive graphic showing the overall picture.

You'll notice quite a few states are at the 'deferred' stage, which means the decision on legislation has been put off to a later date. A lot of these deferrals are on safety grounds: the argument from utility companies is that feeding power into household wiring (rather than just taking it out) comes with risks, and that more needs to be done to protect both consumers and the power grid.

The UL 3700 safety certification, freshly put into place this year, should help here. Plug-and-play solar panels with this certification attached will have built-in safeguards to prevent systems from being overloaded and to stop power flowing back into lines. It's a badge to look for if you're buying this kind of equipment.

Home battery installations

Home battery tech is separate but related, and as Ars Technica reports, records are being broken for battery installations: 673 megawatts of energy storage were brought online in the first quarter of 2026, the highest that figure has ever been.

The key driver here matches up with plug-in solar: rapidly rising electricity costs. The batteries can either store energy from rooftop solar panels, or bank electricity at off-peak times ready to be used during on-peak times. Plus, these appliances offer protection against power outages and help save money.

Unlike plug-in solar panels, home batteries do require a professional installation, the cost of which can be added on top of a typical $10,000-and-up price of the battery itself. It'll take years to pay that back in savings, but it will be paid back — it depends largely on whether you're using solar panels, how many panels you're using, and your home's electricity demand.

There are even moves to tap into this stored energy to help meet the huge energy demands of AI. Companies including Tesla will pay you on an ongoing basis if you allow them to control when your battery charges up and releases power — helping to manage stress on the overall power grid, especially during peak times.

While today's plug-in solar systems aren't designed to connect to big home batteries directly — though they can certainly operate alongside each other in the same home — a selection of them now come with their own portable batteries. As both technologies get more common and issues like safety certifications get sorted out, it's certainly plausible that future plug-in solar kits will be able to feed home batteries.

With the potential cost savings, worries over power grid reliability, and the increasingly convenient (and legal) ways to get all of this set up, it's no wonder that plug-in solar and battery energy technology is growing in popularity — and all the signs are that these devices are likely to become much more widely used in the near future.

Lego is adding new sets all the time, and often I've been so excited to see what's new on the roster that I haven't given any thought to what might be being shunted into the great Lego brick bin in the sky, to make room for the new arrivals. Browsing the Lego website, I came across the 'Retiring soon' section and was appalled to see some of what I would consider absolutely classic sets there.

Firstly, Lego Gringotts. The brick version of the Harry Potter wizarding bank has everything I'd ever want from a Lego set. The two-part kit includes the haphazard above-ground building — complete with goblins and Galleons — as well as the meandering and magical underground vaults, accessed via a rollercoaster train track. Oh, there's a dragon down there, too. This set is already sold out in the US.

My second big surprise is that the Lego Mona Lisa is set to retire. If a bona fide masterpiece is up for the chop, then what is truly safe? Scroll down for 8 more sets that are on their way out — they're already disappearing from Amazon, but there's still time to pick one up directly from Lego before it disappears forever.

• In the US? Here are the the sets retiring soon in the US

Don't miss it

• Ads for fake air conditioners are plaguing Facebook and YouTube
• These appliances promise high performance features and claim to be ground-breaking
• UK advertising regulator warns you should be sceptical and report them

The UK is having its share of sweltering heatwaves this summer and there’s never been a bigger demand for the best fans and air conditioners — but that's also come with a wave of fake air conditioning adverts.

Adverts for portable air conditioners allegedly ‘designed by former NASA engineers’ that can cool down a room ‘in less than 90 seconds’ are being pushed to consumers across the likes Facebook and YouTube. Portable air conditioners have been going out of stock pretty much everywhere — more recently Meaco’s Cirro lineup — so appliances from trusted brands are becoming a lot harder to come by as the UK is gripped by high temperatures

The advertised air conditioners claim to pack a punch all while having affordable prices, ranging between £70-£120 according to the BBC. Additionally, these product listings often feature fake customer reviews with overwhelmingly positive comments on performance features.

Civil engineer and content creator, Stuart Matthews, is just one online persona that’s raising awareness; “if it sounds too good to be true, it’s not ‘probably’ a scam these days, it definitely is a scam,” he shared in a YouTube video.

In one of his most recent unboxing videos, Matthews purchased one of the cheap air coolers, taking it apart bit by bit to give a closer look at the inner workings of these appliances — and they don’t work in the same way as proper air conditioners.

Here's how to spot a fake

The product he showcased was sold as a ‘mini portable air cooler’ with a small water tank that can ‘chill quite a sizable room by a number of degrees very quickly’. Once he took the machine apart, Matthews found what he described as ‘cardboard fins’ that essentially soak up water from the tank, which the fan blows air through at a very weak speed — all of which he forked out £70 for, when he thinks it’s worth no more than £5.

With high demand, users in need will often take the first appliance that’s put in front of them, giving companies more room to scam, and now the Advertising Standards Authority (ASA) is officially warning you. But if you’re finding it difficult to tell the difference between legitimate and misleading adverts, the regulator has issued a few tips.

As mentioned, one of the biggest things to note is the overuse of positive reviews and comments that report life-changing results, so if an advert claims a small fan can cool a room in a very short space of time, be sceptical.

Just with the advert shown in Matthews’ video, you should also be wary of lengthy backstories and bold claims, i.e. “an ingenious invention that’s disrupting the £5 billion air conditioning industry” — a bold claim for a product that no one has heard of.

Additionally, a majority of the adverts seem to be AI-generated, with inconsistencies such as spelling and grammar errors, which you should also keep an eye out for. If you think you’ve run into a fake air conditioner advert, you can file a report on the ASA website.

Philips Hue bulbs are a hugely popular smart lighting solution, and with good reason. But if your setup consists only of Hue bulbs (and a hub), you're missing a trick. The brand makes a range of accessories that can make a major difference to how you use your smart lights, and most are very affordable too. I asked the TechRadar team for some of their favorite cheap smart home upgrades, and almost all the answers I got back were Philips Hue accessories, so I decided it was worthy of its own article.

Entertainment Editor Matt Bolton is a big fan of his Philips Hue Smart Button, a compact, simple, wireless switch. "I stuck the Smart Button on my wall next to my regular light switch, giving me a way to control just the lamps in my living room separate to the other lights," he says. "It's so nice and easy, and no rewiring needed."

Matt also makes use of the Philips Hue Smart Plugs, which can be used to integrate non-smart lights into your Hue ecosystem. "I use the Hue Plugs to add little lamps that are too small for Hue bulbs into my lighting setups," he says. "I also use it for my Christmas tree lights every year, so I can plug them in somewhere awkward, but I can still turn them on and off at will."

Senior News Editor Mark Wilson is a big fan of his Philips Hue Tap Dial Switch. This physical switch has four buttons and a dial, and can control nine different actions; it's a more complex alternative to the Smart Button. "I hate using my phone or voice controls for smart lights. My favorite feature is turning the dial to dim my Hue lights — it's so much better than tapping the buttons on other switches," says Mark. "It’s simple to use, while also being really versatile thanks to those four buttons, which can set scenes in different rooms."

Homes Editor Cat Ellis has a slightly different suggestion: if you're finding regular Hue bulbs too expensive, she recommends checking out the much cheaper Essential range. "I put a regular Philips Hue bulb and a Hue Essential bulb side-by-side in identical lamps, and it was almost impossible to tell the difference when shifting colors — I could only really notice a distinction when dialing down the brightness."

A smarter setup

• The Google Home Speaker supports wireless connectivity to the Google TV Streamer
• This gives a simple way to curate your own home theater setup
• You can connect your Google Home Speaker through your Google TV device, or via the Google Home app

Google’s new Home Speaker comes with a slew of much-needed upgrades, but its support for wireless connectivity with the Google TV Streamer is a tool users have been pining for since the company started making smart hubs.

As well as its Gemini-powered smarts and 360-degree audio redesign, Google now lets you to wirelessly pair the Home Speaker with your Google TV device, allowing you to ditch your TV’s built-in speakers and set up a home theater system. Pairing just one Google Home Speaker works, but you’ll get the most out of your setup if you have two.

The company announced its initial plans to develop the feature in 2020 when it unveiled the Nest Audio, its first smart speaker, but the functionality never arrived. “Google Home Speaker now works together with your Google TV Streamer. You can pair up to two speakers with a Google TV Streamer to turn your living room into a mini home theater with spatial surround sound,” the company detailed in a blog post.

Surround-sound systems are integral to most entertainment fanatic’s setups, but they don’t always have to feature a multitude of different types of speakers — some people simply rely on the best sound bars to boost their audio. Though the Google Home Speaker isn’t necessarily suited to seasoned audiophiles, it gives novices an inexpensive and hassle-free way to enhance their streaming experience.

It hasn’t been impossible to hook up wireless speakers to the Google TV Streamer, however, as the option to use the best Bluetooth speakers has always been there. However, because the Google Home Speaker’s function relies on Wi-Fi, the bandwidth is much bigger. This means it also supports Dolby Atmos which, for a cost-effective home theater setup, is quite a fair perk.

Audio champions such as Sonos and Bose have offered wireless connectivity with third-party streaming devices for years, so the Google Home Speaker’s functionality is far from new. That said, it’s only recently that TV manufacturers have decided to jump on the bandwagon and sell speakers of their own.

Over the last 18 months or so, brands including Amazon, LG and Samsung have released their own speakers to allow wireless connectivity with their range of TVs — so Google is playing catch-up here.

How to pair your Google Home Speaker with your Google TV Streamer

Once you’ve set up your Google Home Speaker for regular use, you can pair it with your Google TV device right from the home screen.

Using your Google TV Streamer remote, click the home button and head to ‘Quick Settings’ at the top of the screen. From there, select ‘Audio output’ from the options, click ‘Connect another device’, then select ‘Google speakers’ and click ‘Getting started’.

After this stage, you should see a list of Google Home Speakers connected to your account in a separate window, and you’ll want to select the ones you wish to pair with your Google TV Streamer. Once you’ve done this, tap ‘Next’ and it should complete your setup.

You can also do this from the Google Home app, as Google details on its support page.

I test a lot of espresso machines here at TechRadar — over a dozen a year — and so far 2026 has delivered a particularly impressive crop. Whether you're looking for your first ever coffee maker or are a seasoned pro hunting for the perfect premium brewer, there's an option for you.

There are so many new espresso machines, in fact, that you might be spoilt for choice, which is where I come in. To help make your decision easier, I've rounded up this collection of the three best machines we've tested this year. Each one has been through our rigorous review process, and received a score of at least four and a half stars out of five.

If you can't see something that quite suits your needs, take a look at our complete roundup of the best espresso machines you can buy today, and the best Nespresso machines if you prefer your morning brew in pod form.

Philips Café Aromis

Release date: March 2026

Score: 5/5

This espresso machine (the Philips Café Aromis 8000 Series, to give it its full name) is a premium coffee maker that looks stunning, makes sublime coffee, and is fun to use as well. It has a menu of 50 drinks — hot and cold — and is astonishingly quiet in use too thanks to cleverly designed noise shielding.

Its milk system is particularly impressive, producing different textures to suit the type of drink you're making, and because the milk never enters the body of the machine itself, it's a piece of cake to keep clean. Just detach the carafe, disassemble it into its three hard plastic components, and wash them in the top drawer of your dishwasher. There are separate carafes for hot and cold milk, and they both work equally well with dairy or plant-based equivalents.

Espresso machines with Wi-Fi or Bluetooth connectivity are quite common, but after connecting your phone, usually all you get is a simple instruction manual. Not here. The Philips Home app is styled like an AI chatbot, and asks you a series of questions about your beans and taste preferences to help tailor the brew setting to your liking. It's certainly not cheap, but it's a superb espresso machine that earned a full five stars.

Read our full Philips Café Aromis review

Philips Baristina

Release date: February 2026

Score: 5/5

Philips has been really nailing it when it comes to espresso machines this year. The Baristina is very different to the Café Aromis, but if you're new to the world of speciality coffee, or just want something reasonably affordable, it's the better choice.

This is the smallest and cheapest bean-to-cup coffee maker I've ever tested, and it's so easy to use, it's a great option for anyone thinking of making the switch from coffee capsules. Just load your beans in the top, fill the water tank, push in the empty portafilter handle, and slide it to the right. The Baristina will grind the perfect dose of coffee into the basket, tamp it down, then slide the whole handle to the left and pull the shot for you.

It's a piece of cake, and much easier to clean than a typical automatic espresso machine because there's no moisture or debris building up inside an enclosed case. The only drawback is that it can't steam milk (unless you pick up a bundle with the standalone milk frother), but Philips has just launched an updated version — the Baristina Latte — that solves that particular issue. I'm very much looking forward to testing it

Read our full Philips Baristina review

Meraki Espresso Machine Gen 2

Release date: March 2026

Score: 4.5/5

The Meraki Espresso Machine Gen 2 (available direct from Meraki in the US, and from Bella Barista in the UK) is the most stylish coffee maker we've tested so far this year, with its satin finish, chrome and wood accents, pivoting touchscreen display, and separate 'towers' for its twin boilers, water tank, and bean hopper. It's huge, but if you've got the space, it's worth every centimeter.

This is a manual espresso machine, but is packed with thoughtful features that make achieving a delicious brew that little bit easier. For example, there are built-in scales beneath the grinder and grouphead to help you grind exactly the right dose of beans, then weigh your extracted coffee and stop the pump at precisely the right time. There's a temperature sensor to help you avoid scalding your milk, and if you really want a helping hand, you can scan a code on a bag of Meraki's own coffee beans, and the machine will adjust its own settings accordingly.

The standout feature, though, is its dual boiler, which is something we rarely see in a home espresso machine. "Not only does it produce exceedingly well-extracted espresso over and over again, it easily froths a range of milks without losing pressure or cooling down," said our reviewer Josh Russell.

Read our full Meraki Espresso Machine Gen 2 review

Dreo Smart TurboPoly Fan 765S: two-minute review

The Dreo Smart TurboPoly 765S is one versatile fan. It can be tall or short pedestal fan, or you can swap out the base and turn it into a desktop model. You can choose from a generous 11 speed modes, as well as six 'special modes', and horizontal or vertical oscillation (or both at once, turning it into a very effective air circulator).

You're spoiled for choice when it comes to control options, too — you can use the remote, touchscreen buttons on the top of the fan head, or adjust settings on your phone using the Dreo companion app.

In that app you'll find an absolute ton of customization options: I've tested some of the best fans on the market, and it's rare to see a fan that offers such precise control over when, where and how it blows. While Dreo does a good job of laying out the app so it's nice and useable, I do wonder how many people really need quite so many options.

So what about that basics? The Dreo Smart TurboPoly 765S delivers an even, effective flow of air, with a great range of settings. The lowest speed is whisper-quiet and gentle yet still perceptible, and the highest is impressively punchy. The Turbo setting — separated out as a special mode — is a miniature tornado. At higher settings, it's not the quietest fan I've used, but neither is it excessively loud.

You're paying a premium for the versatile form factor, as well as the extensive customization options and smart functionality. If you don't need all those things, there are cheaper, equally effective fans that'll fit the bill better. However, if flexibility and precise control is what you're after, the Dreo Smart TurboPoly 765S is a standout choice.

Dreo Smart TurboPoly Fan 765S review: price & availability

• List price: $159.99 / £169.99
• Available: US, UK

At list price, the Dreo Smart TurboPoly fan 765S costs $159.99 in the US and £169.99 in the UK (which equates to about AU$230, though at the time of writing it's not available in Australia). That puts in in the premium price bracket for fans, but it goes some way to justifying the cost with its versatile desktop-or-pedestal design and smart features.

That's especially true when you compare the wider market alternatives. For example, the original Shark FlexBreeze costs $199.99 / £199.99 / AU$249.99 at list price. The Shark option lacks smart features, but it can be used cordless (whereas the Dreo can't). Another alternative is the Meaco 1056P, at $189.99 / £149.99 (about AU$270). This is the model I have at home, and it's less versatile than the Dreo TurboPoly 765S, but quieter at higher speeds.

If you don't need app control and are happy to commit to either a desktop or a pedestal model, there are cheaper options available to you.

• Value for money score: 4 out of 5

Dreo Smart TurboPoly Fan 765S specs

Dreo Smart TurboPoly Fan 765S review: design

• Versatile design can be a desktop or pedestal fan or air circulator
• App control is excellent; buttons / remote best for basic functions
• Wide speed range, precise oscillation control and multiple special modes

As fans go, the Dreo Smart TurboPoly 765S is one versatile performer. You can choose from a generous 11 speed modes, as well as six 'special modes', horizontal and vertical oscillation, and a timer option. You can direct the fan head at a specific target, or unleash the full range of oscillation to use it as an air circulator.

It can be used as pedestal fan, and in this mode it's possible to adjust the height to a taller or shorter floor-standing option. Alternatively, you can remove the base altogether and swap on a different one to turn it into a desktop fan. I especially like the design of the tabletop base — its opening mechanism protrudes so when you press it down on a flat surface the legs extend outwards to form a stable base.

The fan feels well-built and sturdy, and the pedestal base is reassuringly heavy, so I was never concerned about knocking it over. I also appreciated the inclusion of a moulded handle on the fan head, which makes it easy to carry it from the top.

Some competitors offer magnetic remotes that snap onto the fan itself when not in use, but that's not the case here. Instead there's a remote control holder that snaps onto the pole. It could feel more intentional but does the job perfectly fine.

There are a couple more advanced features the Smart TurboPoly 765S lacks. It can't be used cordless, so you'll have to commit to staying near a power outlet. There's also no misting capability — this is a newly popular concept in the fan world, and appears on a handful of modern fans including the Dreo 516S. It can be a bit of a game-changer if it's really hot.

App and controls

That 'S' in the product code tells me there's an app I can use to control this fan. I can't overstate how jam-packed with options this app is. You can use it to turn the fan on and off, switch modes or adjust fan speed, and change the angle of the fan head. You can also precisely set the oscillation angles, including an option for asymmetrical oscillation.

There's a scheduling area where you can either choose when the fan will go on or turn off, and you can also set it to come on at a certain time (and speed / mode) on certain days. One minor missed opportunity is that you can't then schedule when it turns off — I wanted to set it to run for a couple of hours each evening as I go to sleep, but that doesn't seem to be possible.

The app is well laid-out and easy to use, although the fact there are so many precise customization options means it can feel fiddly at times. If you don't want to get your phone out, you can also control the fan using the remote control, or via touchscreen buttons on the top of the head.

These are responsive, and, to a point, straightforward. Changing the speed, swapping modes or adjusting the angle the head is pointing in is easy. However, for fine-tuning I found it far easier to use the app. (In fact, I had such trouble working out some of the functions that I emailed Dreo's general customer services address to help — and they get major brownie points for replying quickly, with a clear answer.)

• Design score: 4.5 out of 5

Dreo Smart TurboPoly Fan 765S review: performance

• A little noisy on higher settings
• Great range of settings, including an ultra powerful Turbo mode
• Easy to direct the air exactly where you want it

Overall, I was very impressed with the Dreo Smart TurboPoly Fan. The speed settings cover a good range, with level 1 delivering a gentle but perceptible flow of air, while level 11 is pleasingly powerful, and Turbo mode all-but blew me away. I can't imagine many situations where you'd need such strong airflow, but it's nice to have the option.

One small but welcome detail is the fact that the windspeed settings cycle from 11 straight to 1. That meant if I knew I wanted a higher setting, I could work backwards and save some button presses.

Also in its favor is how precisely you can adjust where the airflow is directed. In static mode, arrow controls enable you to easily change where the fan head is pointing. It's also possible to finely adjust the vertical and horizontal oscillation; even making it asymmetrical if you want. And of course, you can extend / retract the pole or swap from pedestal to desktop mode if you want to alter the height more dramatically.

I used it to keep me cool in my home office during two UK heatwaves, and adjusted it to a very narrow range of oscillation where it was essentially just blowing from side-to-side on my back. The effect was absolutely dreamy.

I also used it as an air circulator (in its full vertical and horizontal range of oscillation) to amplify the effects of our newly-purchased portable air con unit. It did an excellent job of rapidly distributing the cool air as it was being pumped in, filling the bedroom much quicker than the AC could manage on its own.

In terms of noisiness, I'd give the Dreo middling marks. On setting 1 it's whisper-quiet, but as I moved up the settings the sound ramped up, and on level 11 it was noticeably louder than my usual fan (a Meaco air circulator). It's certainly not the noisiest fan I've come across, though.

Moving on to the special modes. They are as follows:

• Normal: runs at fixed speed
• Auto: speed increases or decreases depending on room temperature
• Turbo: runs at maximum speed
• Natural: speed fluctuates to mimic a natural breeze
• Sleep: decreases speed after 30 mins, up to two times
• Custom (via Dreo app): speed changes at specified times or temperatures

I was pleased to see there's a Sleep mode included, and the setup for this one is pretty standard, allowing you an hour to drop off. It's worth pointing out that the lights on the Dreo Smart TurboPoly 765S switch off automatically as standard a few seconds after you've finished adjusting them — something I appreciated as I hate to have a glowing LED illuminating my room as I'm trying to sleep. (You can change this setting if you prefer the display to stay on.)

Auto mode is useful, too, if you're using the fan throughout the day. The ambient temperature measurement seems accurate, and matched that of my other fan.

I wasn't so enamored with the Breeze mode. I've seen this mode listed on a few different fan models recently, and have always been curious about it. On test, though, I found the fluctuations in speed and accompanying shifts in noise distracting more than anything. That said, it did feel somewhat like a natural breeze, and I can imagine some people enjoying this effect.

• Performance score: 4.5 out of 5

Should you buy the Dreo Smart TurboPoly Fan 765S?

Buy it if...

Don't buy it if...

How I tested the Dreo Smart TurboPoly Fan 765S

I tested the Dreo Smart TurboPoly 765S over three weeks in June/July, which happened to encompass two UK heatwaves, with temperatures reaching 37C or higher (around 98F). I used it extensively during the day while working from home, as well as at night, and tested all the special modes. I also tried out all the control methods, including digging into the app. I compared my findings with other fans I've used, but predominantly my trusty Meaco air circulator.

Read more about how we test

• First reviewed July 2026

The recent heatwaves sweeping the UK has led to a run on the best fans and air conditioners — and that also includes the new Meaco Cirro portable air conditioner, which lauched just last month.

Following high demand over the past few weeks, Meaco shared on its Instagram page that it will be restocking its Cirro range of air conditioners. This gives you another shot at scoring the air conditioner as UK temperatures soar again, but be warned — demand is going to be just as strong this time around.

As temperatures rise, so does the demand for air cooling devices. The Cirro range consists of six different models (it has cooling-only and cooling-heating hybrids in sizes 12,000, 14,000, and 16,000 BTU), but each one completely sold out on the Meaco website. The 12,000 BTU cooling-only model was restocked just yesterday (July 8), and it went like hot cakes.

The models being restocked are as follows. The Cirro 12,000 BTU and Cirro 16,000 BTU cooling and heating models will be restocked today (July 9) at 10am, and the Cirro 14,000 BTU cooling and heating model will be restocked on Friday July 10 at 10am.

This looks like your final chance to get your hands on one of Meaco's Cirro portable air conditioners this summe, as the company revealed that it won’t be restocking its cooling and heating devices until September. At the moment, Meaco’s cooling-only models are still unavailable and won’t be restocked until April 2027.

If you’ve had your heart set on one of Meaco’s latest air conditioners but miss out on the restock, all is not lost — a number of third-party retailers that are stocking Meaco’s range of fans and other cooling devices.

Argos is currently stocking Meaco air conditioners such as the Meaco Cool MC 8000CHBTU and the MeacoCool MC Series Pro 9000BTU portable air conditioner, while John Lewis has replenished its stock with Meaco fans as well as its coolers.

The Shark ChillPill is one of the best personal fans around, but it's selling out fast, and if you want to grab one for delivery this week you'll have to be quick. Right now the only option available for rapid delivery is the Shark ChillPill in Dragonfruit for £129 at Amazon.

All other colours are back-ordered, with the silver Cloud version not available until the end of July, and more popular options like Matcha green unavailable for at least six months. If you want your fan this side of Christmas, don't hang around.

I've been keeping a close eye on stocks of various fans during this summer's heatwaves, and personal coolers have been especially popular. In fact, according to a report published by the Guardian this morning, Britons are expected to buy eight million mini fans this year. Most of those will be cheap, low-quality devices sold for just a couple of pounds or even given away free, and last year it was calculated that 55% ended up in landfill.

You certainly don't have to spend £129 on a fan to keep yourself comfortable, and there are many cheaper options available. However much you spend though, it's worth taking care of it, and hanging onto it for as long as possible to prevent unnecessary e-waste — and to make sure you're ready when the temperature starts to climb again next year.

Hands-on with the ChillPill

If you do opt for the ChillPill, I think you'll be pleased. It's a compact and lightweight fan with 10 different speed settings, and a choice of three attachments: the standard fan, a misting fan with its own water reservoir, and a cooling plate to place against pulse points when you're getting uncomfortably warm.

I bought a ChillPill myself after trying one out, and it's been very welcome during my daily office commute — particularly when the train is replaced by a bus service. The misting attachment is especially effective, and can be filled from your drinking water bottle, though I recommend using the intermittent mode rather than continuous misting so the reservoir lasts longer between fills.

For more cooling options, take a look at our complete list of the best fans, which includes plenty of desk, standing, and tower fans to keep you comfortable at home.

The AeroPress Steel has sold out twice, but now it's back in stock in the UK, just in time for your summer camping trips. It's a super-tough, travel-friendly coffee maker that lets you make a tasty brew with fresh beans on the move, and it's available now direct from AeroPress for £159.99.

I've put the AeroPress Steel to the test myself, and was surprised by how little it weighs considering its all-metal construction. Although it probably won't be your go-to coffee maker for backpacking adventures where every gram counts (for that you'd be better with an AeroPress Go), it's not going to weigh you down unnecessarily.

Its accessories have received the stainless treatment as well; rather than the plastic stirrer and scoop provided with a standard AeroPress coffee maker, the AeroPress Steel comes with metal versions, which should give you many years of happy brewing.

If you're worried about the metal chamber conducting heat, you'll be pleased to know that it has double-walled insulation that keeps your coffee hot and hands safe. When using the steel brewer, I found that the outside was never more than pleasantly warm to the touch, and never uncomfortable to hold.

The only thing to watch out for is the metal filter cap at the bottom, which will heat up when you're extracting your coffee, so make sure you allow it to cool before unscrewing it and ejecting the used coffee grounds.

Find your grind

The AeroPress Steel is a great partner for the AeroPress Manual Coffee Grinder, which I also had the opportunity to try recently. Unlike most travel-friendly coffee grinders I've tested, which use blades that chop coffee beans into shark little chunks, the AeroPress grinder uses stainless steel burrs that deliver consistent, even results.

You can experiment with different extraction times by adjusting the grind size, with an impressive 60 settings available, and the hopper holds up to 25g of beans at a time, which is enough to prepare two espresso-style drinks on the move.

The grinder has an easy-turn handle with a large, circular handpiece that's comfortable in the hand, but also comes with an attachment for a power drill (yes, really) if you'd rather spare the elbow-grease. Small magnets hold the handle against the side of the grinder when not in use, and the whole package is compact enough to slide neatly into your AeroPress (whether it's the Steel or a traditional plastic) for easy storage.

The AeroPress Manual Grinder is available direct from AeroPress for £199.99.

Fan technology has made huge leaps in recent years, with more powerful and quieter motors, misting attachments, and AI-powered person-tracking all promising to keep you extra cool when the weather warms up. But which fans actually deliver, and actually keep you feeling refreshed on sticky summer days?

We test dozens of new fans every year on TechRadar, and to help you pick the best one for you, I've rounded up the five that have really impressed me over the first half of this year, from brands including Shark, Dyson, and Dreo.

Dyson HushJet Mini Cool

Release date: April 2026

Score: 5/5

It's a lot pricier than your average handheld fan, but the Dyson HushJet Mini Cool is also a lot more powerful, and unlike flimsy plastic devices, it's built to keep you cool for many summers to come. Despite its small size, the HushJet Mini really packs a punch, even on its lowest setting, and the highest options feel like a cold hairdryer blowing in your face. It's comfortable to hold, can stand on its end for use as a desk fan, and comes with a strap that lets you wear it around your neck. You can twist the angled nozzle to aim the airflow directly at your face and neck for quick relief on sweaty days.

Dyson claims battery life of up to six hours, but in my tests it continued running for almost exactly six and a half, which is impressive for such a compact device that shifts a lot of air even on its lowest setting. It's not quite as quiet as the Shark ChillPill below, despite Dyson's HushJet nozzle, but that's understandable considering it's basically a portable tornado.

Read our full review

Shark ChillPill

Release date: March 2026

Score: 4.5/5

Another excellent handheld fan, the Shark ChillPill has a unique twisting design that lets you place it on a desk and angle the airflow at your face, plus three different cooling attachments: a regular fan, a misting fan (with a small reservoir for water), and a metal cooling plate that you can press against pulse points. The misting feature is my personal favorite, with continual and intermittent options — the spray is fine enough to evaporate on contact so it won't make your hair and clothes wet.

It loses half a star compared to the Dyson fan due to its higher price tag and less powerful motor — the ChillPill can reach up to 25,000rpm, while the HushJet Mini Cool can reach 65,000rpm — but the Shark is quieter. During my tests it ranged from 46dB on its lowest setting through to 67dB on the highest, making it a more discreet option in public.

Read our full review

MeacoFan Sefte Pro 10in Table Air Circulator

Release date: May 2026

Score: 4.5/5

Air circulators are designed to move a large volume of air around a room rather than direct a focused stream in your direction, and the 10-inch version of the MecoFan Sefte Pro does this extremely well. You can run it directly from the mains, or from its rechargeable battery, so you can carry it around the house with you. This works particularly well when paired with the Sefte Pro's Eco mode, which adjusts the air circulator's power depending on the temperature.

I used the MeacoFan Sefte Pro during the last heatwave, and it was a real life-saver at night. Its sleep mode is almost silent, and its remote control means you don't need to get out of bed to activate it, and it's also available as a pedestal fan if you prefer. The biggest drawback is that it's not currently available outside Europe.

Read our full review

Dreo Smart Misting Fan 516S

Released April 2026

Score: 4/5

The Dreo Smart Misting Fan 516S is another fan that keeps you extra cool with a super-fine spray of water, and our reviewer Harry Padoan said that "it added a nice degree of coolness without making any mess or feeling too intense". The 1.3-liter tank is large enough to keep misting for hours on end, and it's easy to switch to fan-only mode once you've had enough.

It's very reasonably priced too, coming in at $99.99 / £99.99 (about AU$140). That's not bad at all for a misting fan with app controls, and compatibility with both Amazon Alexa and Google Home, so you can operate it using voice commands.

Its lowest mode is quiet enough to avoid disturbing your sleep, though Harry found the turbo option loud enough to break his concentration, so it's best reserved for exceptionally sticky days when you want to just slump on a chair and do nothing.

Read our full review

Dyson Find+Follow Purifier Cool

Release date: June 2026:

Score: 4.5/5

As you can guess from the name, this fan's key selling point is its ability to detect motion and follow you around the room, so you're never beyond range of its refreshing jet of air, even when you're doing chores, working out, or pottering about the kitchen — all of which are usually extremely unpleasant in hot weather. Paired with its extra-wide range of motion, this could make it the only fan you need.

It has Dyson's signature bladeless design, and our reviewer John McCann said it "delivers smooth air flow that feels like a natural breeze moving through your home, rather than the harsh buffeting you get from some other propeller and tower fans." It's extremely quiet at night (dropping to as low as 20dB), but delivers real cooling power as well.

It's the most expensive fan in this roundup (indeed, it's one of the priciest fan/air purifier combos on the market) but it's hard to argue with its sheer performance. If you've got the budget to spare, it's packed with premium features that really work. I only wish it offered vertical oscillation as well as horizontal.

Read our full review

• Air frying, steam cooking and steam frying in one device
• 9.5L in the MegaBasket or 3L + 6L in separate baskets
• It's on sale for £258.99 (about $350 / AU$500)

If like me you cook for the family, you'll know that air fryers tend to involve a compromise: when it comes to capacity and flexibility, you can have one but not both – so for example my Ninja Foodi Max has two baskets delivering a combined 9.5L of cooking capacity and multiple modes, but neither basket is big enough for me to roast a really big chicken. Philips' solution is what it calls the MegaBasket.

The MegaBasket is making its debut in the Philips Airfryer 5000 Series MegaBasket, which gives you a choice: you can use the single MegaBasket to get 9.5L of cooking capacity, or use split baskets of 3L and 6L respectively.

The 5000 Series also addresses another air fryer irritation: cleaning. Because this cooker has a steam function, you can get it to steam clean itself.

Philips MegaBasket air fryer: key features and price

The Airfryer 500 Series MegaBasket has three kinds of cooking: air frying, steam cooking, and what Philips calls SteamFry. That combines air frying and steam cooking to keep your food nice and juicy in the middle while the air fryer crisps the outside. It's particularly handy for food such as chicken breasts, which can get awfully dry in a normal air fryer if you don't marinade them for a good while first. It also helps vegetables retain their nutrients.

Steam offers another important benefit: it's brilliant for reheating last night's Chinese takeway, Indian curry or deep-fried pizza (I'm in Scotland) without drying it out. As someone who tends to over-order from the chippy and have leftovers the following day, that's enough to sell the Philips to me, and to differentiate it from the Ninja Foodi FlexDrawer, which has slightly larger capacity but lacks the steam function.

This isn't the biggest air fryer you can buy — the aforementioned Ninja has 2 x 5.2l or 1 x 10.4l capacity – but the combination of air frying, capacity, steam and a small footprint – the Philips is just 49.6 x 32.9 x 35.5cm — makes this look awfully attractive for family meals and entertaining alike.

The Philips Airfryer 5000 Series MegaBasket with Steam has a price of £258.99 (about $350 / AU$500) and it's available from Amazon UK now.

Getting started with smart home can feel intimidating, not least because it feels like there's sure to be a hefty cost involved. It doesn't have to be that way, though. I asked the TechRadar team for their top affordable smart home recommendations, and they came through with some real winners. All the gadgets featured below come with the stamp of approval from TechRadar, will make your home that little bit more convenient, and won't cost you more than $50 / £50. Hit the 'View details' button to learn more about each one.

Budget-friendly smart home

The temperature is rising again, and fans are selling out fast, but you don't need to settle for something sub-par that will just waft warm air around. I've done the hard work for you, combing through online stores to bring you a list of eight top-quality fans from big names that are ready to dispatch right now — and they're all under £100.

There's something for every room here, including compact desktop fans for working, and extra-quiet tower fans to help you sleep better at night, plus lightweight handheld fans to keep you comfortable on the move,

Remember, they're likely to sell out fast as the temperature climbs, so I'd recommend grabbing one while you can. Personally, I've just opted for the MeacoFan Sefte 8in Air Circulator, which moves a large volume of air and is ideal for bringing the night breeze indoors when the temperature drops outside in the evening. Which one will you pick?

Quality fans under £100

• Aldi is launching a new outdoor lamp range
• Each lamp is solar-powered and comes in two styles with three color choices
• The cost just £4.99, making them an affordable way to give your garden a glow-up

We’re seeing more and more affordable tech gadgets appearing in the middle aisles of budget supermarkets these days — and if you’re looking to give your garden a summer makeover, Aldi just unveiled a new range of solar-powered garden lights.

The lineup, which goes on sale on July 9, consists of two styles of outdoor table lamp, mushroom-top and flat-top, both of which are available in three colors: black, mint, and beige, so you should be able to find a colour that fits in with your garden decor.

Each lamp costs just £4.99, making them an affordable way to give your garden a glow-up with Aldi proving once again that you don’t need to spend a lot of money on the best smart lights in order to brighten up your home and garden.

Aldi’s new lighting range isn't, of course, in the same ballpark as smart lights from the likes of Philips Hue or Govee. There’s no app and no controls to fiddle with, and because they’re solar powered, placing them in sunny spots in your garden will ensure they have enough juice to last through a whole evening of outdoor dining or partying.

If there’s one thing we’ve learned from national treasure Nigella Lawson is that summer parties aren’t just about good food and drinks — the setting and decor are just as important, and lighting plays a big part in creating the perfect atmosphere.

It’s not only budget brands like Aldi that are jumping on the outdoor lighting bandwagon — if you want app-based features such as the option to change the colour of your lights, the big smart home brands are getting in on the act too.

Govee’s recently released smart string lights marked the brand’s first step into solar lighting costing £119.99. Though this is a little more pricey than the average solar-powered light , Philips stills takes the top spot on the price front — its own Festivia Smart Globe String Lights are one of our favorite garden gadgets for giving your outdoor space an instant lift.

Before I tested and reviewed the Ninja AutoBarista Pro, I had tried every kind of coffee brewing method over the years. I ground my own beans with a high-end 20-setting electric burr grinder. I researched how to get the ideal grind for each type of bean and brewing method. Grind size is important, because it determines the speed that water flows through your coffee grounds and therefore the amount of extraction.

As a general rule, you'll want a coarser grind for a French press or for cold brew made in the refrigerator. Medium-coarse works well for pour-over. A typical automatic drip machine works best with a medium grind. A moka pot works well with medium-fine. The finest settings are best for espresso machines or Turkish coffee.

How your beans are roasted also plays a part in how coarsely you'll want to grind your beans. Darker roast beans work best with a slightly coarser grind, while lighter roasts work better when ground slightly finer.

When grinding your own beans, you'll have to account for both your roast and your brewing method. If your coffee comes out more bitter than you'd like, you'll want to grind your beans more coarsely. On the other hand, if your coffee comes out sour or weak and watery, you'll want your beans ground a bit more finely.

Figuring all this out and adjusting the grinder (known as 'dialing in') doesn't require a chemistry degree, but it does require some some trial and error on your part. Then along comes the Ninja AutoBarista Pro with Grind iQ, which removes the need for guesswork. Just pour in your whole beans, and Grind iQ takes it from there.

The first time you put new beans into the Ninja AutoBarista Pro's hopper, Grind iQ will determine the ideal grind size based on your particular beans. This process takes about five minutes or so, and it does expel a bit of coffee, but then it's good to go.

Whether you're making a regular cup of Drip Coffee, Espresso, Iced Coffee, or Cold Brew, the built-in stainless steel burr grinder grinds your beans just right for every cup. The machine automatically determines which of its 50 grind settings to use. No guessing or trial and error. It's just one less thing you need to think about before you've had that first cup of coffee in the morning.

EZVIZ EP4: one-minute review

Fitting a video doorbell or security camera is often a non-starter if you rent or live in an apartment where drilling into the walls isn’t allowed. That’s where the EZVIZ EP4 Wire-Free Peephole Door Viewer comes in — by fitting through your front door’s existing peephole, it brings almost everything you’d get from a full video doorbell, without any damage that could upset your landlord.

The physical setup is incredibly easy and took me just 10 minutes to complete. After you’ve unscrewed the old peephole, the EP4 securely clamps onto the door without a power tool in sight.

Once it’s running, the footage captured is very clear, giving you a detailed look at anyone outside. The companion app is simple to use and intuitively designed, making it effortless to check live feeds, use the two-way talk feature, or adjust security settings.

When it comes to saving video footage, EZVIZ doesn’t lock you into a subscription plan like some rivals. While the company includes a free trial of its cloud subscription service, you aren’t forced to pay for it afterwards. If you want to skip the recurring fees, you can opt to install a local microSD card (up to 512GB) to store clips locally.

However, the EP4’s AI facial recognition has a notable quirk. Although it's smart enough to identify who is at your door, there’s currently no way to stop the app from sending you notifications when it spots someone you know — including you. Because you can’t tell the camera to ignore certain individuals, you’ll be alerted every time you walk through your own front door.

EZVIZ EP4: price and availability

• List price £229.99 (about $300 / AU$440)
• Available in the UK, but not the US or Australia
• No subscription necessary if you use a microSD card

The EZVIZ EP4 Wire-Free Peephole Door Viewer is available in the UK for £229.99 (about $300 / AU$440), but I’ve seen it discounted to as little as £159.99 during sales events. It’s not yet available in the US and Australia at the time of writing, but older models are, so hopefully the EP4 will launch more widely soon.

If you want to store your videos at home subscription-free, you’ll also need a microSD card (up to 512GB), so factor this into the cost. If you’d prefer to store footage in the cloud, you’ll want an EZVIZ CloudPlay subscription. After a 30-day free trial, there are three plans to choose from:

• Value score: 4.5/5

EZVIZ EP4: design

• Discreet external camera
• Very simple to fit without damaging door
• Internal screen projects an inch into the room
• Visitors might not spot the doorbell button

The EP4 has two main parts: the camera, which has a cable that threads through the peephole in your door, and a screen that sits on the inside. The camera has a doorbell button below the lens (though visitors might not notice it because it's at an unusual level), a motion sensor at the top, and a speaker and microphone on the side.

It’s compatible with doors between 1.4 x 4.1 inches / 35 x 105mm thick, with a peephole diameter between 0.6 inches and 2 inches / 14mm and 50mm. That’s a wide range, and should be fine for the vast majority of internal and external doors, but it’s worth measuring yours first just to be sure. You can remove the peephole from your door by simply unscrewing it, though if it’s particularly tight, you might need to use a pair of pliers to get it started.

To fit the EP4, start by measuring the thickness of your door using the card template provided, and choose the appropriate pair of screws, indicated by the instruction manual. These will be used to clamp the EP4 onto your door. Peel the paper off the 3M tape on the back of the camera unit, position it on the outside of your door (I recommend using a spirit level to get it straight), thread the screws and data cable through the peephole (you can roll a piece of paper around them to avoid snagging), and press down to secure it.

Then tighten the screws a little, slide the mounting plate for the screen into place, tighten the screws the rest of the way, plug in the data cable, and slide the screen into place. The whole process takes no longer than 10 minutes, and when you want to remove it, there’ll be no damage to your door.

It’s a clever design, and the exterior camera is discreet (it comes with stickers to put on your door if you want to warn visitors they are being recorded), but it’s worth being aware that the interior screen stands about an inch proud of the door, so you’ll need to be very careful if it opens opposite a wall.

You can detach the screen unit to charge it via a microUSB cable (supplied with the EP4) and insert a memory card. It’s a shame there’s no hot-swappable battery — you can’t use the camera and doorbell while the unit is charging — but battery life is quite respectable. EZVIZ suggests up to 120 days, though this will depend on how many times the camera is triggered and how often you use the internal screen to see what’s happening outside.

• Design score: 4.5/5

EZVIZ EP4: performance

The EP4 is an ingenious home security device that provides many of the advantages of a video doorbell or home security camera without needing to make permanent changes to your property. It’s a great pick for an apartment, with excellent picture quality and smart notifications, though it’s worth being aware of a few drawbacks — particularly when it comes to person recognition.

The resolution of the internal screen is fine, and you’ll immediately benefit from a field of view that’s much wider than your original peephole, but it doesn’t do justice to the EP4’s 4K camera. To see footage in its full 4K glory, you’ll need to use the Ezvizlife app, which also gives you access to all the EP4’s settings, as well as event history, saved recordings, call logs, two-way talk, and static photos.

Footage in the Ezvizlife app is incredibly sharp, and there’s very little lag between events happening outside and the camera starting to record. You’ll notice a delay when using two-way talk, but it’s only a couple of seconds, and no worse than some much higher-end video doorbells we’ve tested here at TechRadar.

When a visitor uses the doorbell, you'll receive an incoming-call-style notification that you can choose to reject or answer to start two-way talk. It's also possible to start two-way talk at any time through the app if you can see someone at the door.

Want to keep your identity private? The app gives you two options: ‘Uncle Tone’, which deepens your voice, and ‘Clown Tone’, which makes it high and squeaky, both of which work well and will effectively disguise your voice if you don’t want to be recognized. Personally, I would prefer an option that doesn’t sound quite so cartoonish, but they’re a welcome feature nonetheless.

I found the fisheye-correction option particularly useful during my testing, along with the AI person-shape recognition, which correctly identifies subjects even when they’re wheeling a bike or carrying a large object that might obscure their body shape.

When a person is detected, the camera will send a notification to the EZVIZ app, and start recording a 10-second video clip, which will be saved on an SD card or in the cloud, depending on which storage option you’ve chosen. You can also choose to watch through the camera live at any time, trigger a recording, or capture a still image.

You can also export videos from your logs at any time, which is very useful if you're unfortunate enough to need them as evidence for the police.

EZVIZ is a Chinese company, and although the app has been localized quite well, some parts are still confusing. For example, if you attempt to toggle a feature that’s still in beta, you will see a notification reading: “The current status of this detection is closed. Please enable the corresponding algorithm in the intelligent detection before enabling this function”.

For me, the biggest drawback — and the one that holds the EP4 back from a better score — is the implementation of facial recognition. In an ideal world, you wouldn’t receive a notification when your own face is detected, and you could disable alerts for other members of your household as well, so you’re only alerted when a stranger arrives. Unfortunately, that’s not an option with the EP4, which notified me that “Cat appeared” each time I arrived home from work.

Facial recognition works very well, and even identifies a person wearing a cycle helmet and sunglasses, but at the moment, the implementation seems back-to-front. In fairness, though, the feature is still in beta, so perhaps the developers at EZVIZ will make that change before its full launch. For now, it's a real problem.

• Performance score: 3.5/5

Should you buy the EZVIZ EP4?

Buy it if

Don't buy it if

EZVIZ EP4: also consider

If you're not sure whether the EZVIZ EP4 is the right security camera/doorbell for your home, here are two other wireless alternatives to consider.

How I tested the EZVIZ EP4

I installed the EZVIZ EP4 on the door to my apartment, having first unscrewed the original peephole. I used it for two weeks, adding myself and my husband as 'familiar faces' halfway through. I used the two-way talk function to speak to him when I received a notification that he had arrived, and we used the doorbell function to speak to one another. I kept recordings on a microSD card once the seven-day cloud storage trial expired, and used the app to review recordings, export videos, and capture still images.

At the end of the test period, I removed the EP4 and replaced my door's original peephole. For more details, see how we test, review, and rate products at TechRadar.

First reviewed July 2026.

Blink Outdoor 2K+: two-minute review

Blink has become the brand you recommend to people who don't really want a security camera. Cheap, painless, owned by Amazon, and a forgiving field of view. The catch was that previous 1080p pictures turned to mush the moment anything moved, or the sun went down.

The Outdoor 2K+ fixes this by capturing would-be crims at 2560 x 1440 in its top "Best" setting. There's 4x zoom for closer inspections, noise-cancelling two-way audio making doorstep conversations less of a shouting match, and an improved low-light sensor that holds color as the light fades before switching to infrared black-and-white. Drop to 1080p 'Standard' or 720p 'Saver', and you'll claw back a bit of battery life.

Blink quotes up to two years from a pair of AA lithium cells, and while I can't fast-forward through two summers to prove it, a fortnight’s daily use barely dented the gauge. There's a USB-C port if you'd rather wire it to the mains with Blink's separately sold weather-resistant adapter, an IP65 rating shrugs off wet weather, and it’s compatible with the existing Outdoor 4 accessory range, so floodlight mounts and battery packs carry over.

Setup should be the usual Blink doddle. Scan the code, follow the app, pair the Sync Module, done in under 10 minutes with no cabling and no electrician. For a first-time buyer, it's about as low-friction as home security gets, although we did encounter some teething problems connecting the kit to a home Wi-Fi network.

Then you discover the real kicker. The Outdoor 2K+ ships with a new Sync Module Core rather than the old Sync Module 2 we were supplied with, and the Core has had its USB port removed. That port was the whole point for subscription-averse buyers: plug in a flash drive, store clips locally, pay Amazon nothing.

Without it, the free experience reduces to live view and motion alerts, while saved recordings, person and vehicle detection and the smarter notifications all sit behind a Blink subscription that starts at £2.50 (about $3.50 / AU$5) a month and rises to £8 (about $10 / AU$20) for unlimited cameras. An older Sync Module 2 still works if you own one, but most people buying this won't.

It leaves the 2K+ in an odd spot. As a camera, it's the best budget outdoor option Blink has made. As a package, it's less optimal. Judge it on the camera and battery life alone, and it's a comfortable recommendation. Judge it on the small print, and you’ve got a new monthly bill the old model didn’t demand.

Blink Outdoor 2K+: price and availability

• List price: £89.99 / $99.99 / AU$119
• Launched October 2025
• Available in the US, UK and Australia

Pitched at the affordable end as ever, the Outdoor 2K+ slots in alongside the cheaper Mini 2K+ and the Blink Arc — a mount that pairs two Mini 2K+ cameras for a panoramic view — as part of the brand's 2K refresh. The one-camera kit includes the Sync Module Core, two AA lithium batteries, and a mount, so nothing essential to buy on day one — unless you want your footage saved anywhere, at which point the maths changes.

That's the rub. The headline price buys you a very capable camera and a deliberately hamstrung storage situation. Anyone who bought the Outdoor 4 specifically to dodge a subscription should know the goalposts have moved, because the bundled module no longer takes a USB stick. Frequent discounting means the camera itself rarely costs full RRP for long, which softens the blow, but the ongoing cost is the number to watch.

• Value score: 3.5/5

Blink Outdoor 2K+: subscription costs

Blink has two subscription tiers to choose from, both offering unlimited cloud storage for recordings for up to 60 days (up to 30 days in the EU and UK). Monthly or yearly billing is available.

• Blink Basic: $3.99p/m | £2.50p/m | AU$4.95p/m
• Blink Plus: $11.99p/m | £8p/m | AU$15p/m

Blink Basic includes support for one device, motion-event recording, live-view recording, instant video access, video sharing, person detection, and photo capture. Blink Plus includes all Basic features, along with unlimited device inclusion, moments capture, notification snoozing and 10% off Blink devices.

Blink Outdoor 2K+: specifications

Blink Outdoor 2K+: design

• Compact and easy to place
• IP65 weatherproofing
• Sync Module Core changes rules

There's nothing here to frighten the neighbours. The 2K+ keeps Blink's small, squared-off black housing, the kind of camera that disappears into a porch corner or sits on a windowsill without announcing itself. It's light, the bundled mount screws to a wall, and you can equally stand it on a flat surface and forget about it.

The IP65 rating earned its keep through sporadic summer showers and wind with no fogging or dropouts. Power comes from two AA batteries hidden behind a sealed cover, or bypass them with USB-C and an optional weather-resistant power adapter, if you'd rather not think about batteries at all.

Like the Sync Module 2, Blink’s bundled Sync Module Core is a similarly small puck minus a USB connection.

• Design score: 4/5

Blink Outdoor 2K+ performance

• 2K is a visible upgrade
• Color night vision is useful
• Smart features cost extra

The Blink Outdoor’s 2K output greatly enhances the chances of identifying strangers. I set it to watch a back garden, and it did an able job of capturing my faux break-in attempts. The 4x zoom is digital, so it softens as you push in, but it's enough to pick up distinguishing features or marks.

Low-light performance is the other win. An improved sensor holds color as daytime fades, while garden lights and street lamps keep footage useful. Let the light go entirely, and it reverts to black-and-white. For genuine color after dark, you can add Blink's separate Outdoor Floodlight Mount.

Motion detection was razor-sharp, even if the default settings felt overzealous. Definitely adjust sensitivity and activity zones in the app to avoid being swamped with notifications about plump pigeons and swaying flora… unless you’re aiming for Springwatch in forensic form.

This is also where the subscription cost bites again: person and vehicle detection — the features that stop your phone buzzing every time a fox crosses the lawn — only switch on with a Blink plan.

Run it free, with the Core module, and you're left with motion alerts and a live view, which is a thinner experience for a 2K camera. As ever, there's no way to view footage on a computer or browser; it's the phone app or nothing.

• Performance score: 4/5

Should you buy the Blink Outdoor 2K+?

Buy it if

Don't buy it if

Blink Outdoor 2K+: also consider

If you're not sure whether the Blink Outdoor 2K+ is the right home security camera for you, here are two others to keep in mind.

How I tested the Blink Outdoor 2K+

• Tested at a domestic property
• Mounted outdoor
• Assessed video, night vision, audio, and battery

I lived with the Blink Outdoor 2K+ as a normal household would, mounting it to watch the back garden. I ran it through all three resolution modes, checked color night vision against lit and unlit spaces, and held two-way conversations to judge the audio. The two-year battery claim is, by definition, untestable in weeks, so I've reported Blink's figure and my short-term experience rather than pretending otherwise.

For more details, see how we test, rate, and review products at TechRadar.

Smeg is best known for its bright, fun appliances that add a splash of color to your kitchen. Its new Musa collection takes a different tack, however, using shades of black with a fun twist that’s only visible when you get up-close. Musa — which includes ovens (both full-size and compact), warming drawers, and induction hobs, with an extractor hood coming next year — is the work of Milan-based studio BorromeodeSilva, which has a background in automotive design. I spoke to co-founder Carlo Borromeo to find out how the studio is bringing that experience to your kitchen, and the challenges experienced along the way.

This isn’t the first time BorromeodeSilva has worked with Smeg — in 2012, the two brands, along with eyewear company Italia Independent, teamed up to create a special-edition denim-clad version of the Smeg Fab 28 fridge. The resulting product didn’t just look cool; it was designed to be practical as well, withstanding regular use in an ordinary kitchen.

So how did an automotive design agency get involved in creating such an unusual product? According to Borromeo, the project came about from a relationship with Roberto Bertazzoni , who pitched the initial concept.

“I'm like, 'No, but that's a terrible idea, you know? It will get dirty,' and they're like, 'Ah, you find a way,'” says Borromeo. “And so we took the project very seriously, and we developed a plasma treatment for the fabric that allowed us to coat it with a protective surface. So, if you touch it, it feels normal, but it's actually stain-resistant, odor-resistant; it doesn't pick up mold or stuff like that. And the fridge came out, and it was a mega success — they sold thousands of them.

“So, that was the beginning of a very fun relationship with the Bertazzoni family and Smeg at home, especially with the Vittorios’ father, Roberto, who became kind of like a mentor. And we kept the relationship going more as a friendship. But then, in recent years, we got back in touch, and they asked me to come and design a few products for them, and it was an absolute joy to rekindle that relationship.”

The brief for the Musa collection was very different. Rather than experimenting with novel materials, the goal here was to make an appliance with the fun personality and character of a Smeg product, but that would also fit into a modern kitchen.

“These kitchens tend to be quite understated nowadays, so we need to figure out a way to add our flair, our fun, our playfulness, but in a context where it doesn't explode too much, but fits in,” says Borromeo. “And this was the challenge about this project.”

There has definitely been a trend towards using natural materials and neutral colors in kitchens recently, exemplified by products such as KitchenAid’s stand mixer with a walnut wood bowl, and Pantone’s color of the year, Cloud Dancer. It’s a far cry from Smeg’s pastel-colored retro appliances, so I asked Borromeo how his team went about designing something that would suit.

“Was it a challenge kind of working with that, to create something unique?” he asks. “I mean, we wanted to do that right away, but as you see, the Musa, it's black and gray. This was done by design because we thought, let's try to see if we can make a product that is Smeg, even if we take away the color, which is the primary thing that identifies Smeg.

“We said, if we have to reduce it to its minimum components, let's try to take away the color as well, and see if we can create a product that is still connecting, that is still fun, that makes you smile, that has a sort of magnetic aura. And I think we achieved it, because I noticed it during [Milan] Design Week. There was a wall with all these different ovens, and Musa was one of them, and immediately, you would notice it. So, it's a product that doesn't scream for attention, but captures it anyway.”

Although the Musa oven might look plain at first glance, get closer and you’ll see the elements that make it interesting and different, despite the lack of color. For example, it has an unusual texture, which comes from BorromeodeSilva’s automotive background.

“We work a lot with classic cars, modernizing them. And so this method of taking character traits and applying them to objects is something that stems from there,” says Borromeo. “Then there’s also a practical thing that helps us a lot, which is our knowledge of CMF — color, materials, and finish — in developing the texture that we use to decorate the objects.”

He turns to the Musa oven. “If you look at it from far away, the window is like a solid, but as you get closer, you notice this stripey texture, which is playful, it's nice to the touch, it gives you more. And also, it gives you a little surprise as you get closer, which is a playful element.”

The other playful element is the window, which is smaller than usual, with rounded corners, prompting you to peek inside. Borromeo called it the portal — or “hublot”, in Italian.

“I think it's a fun idea that kind of defines the spirit of the product,” he says. “Usually, when you have these ovens, you try to have the largest possible opening because it's functional; it makes sense. In this case, we tried to actually reduce it, and we created like a portal — a smaller window that maybe looks not logical, but in the end, it invites you to peer in. So, it's trying to communicate to you in a certain way. It becomes like a little portal into your kitchen, into your food.”

He explains that the oven established a “design language” for the whole collection, and four of the studio’s 15-person design team already have it in their homes — including him. If you want your own, prices start at £399 (about $530 / AU$770).

I've reviewed a few robot vacuums in the last year sister site Tom's Guide, but I'd yet to try one from powerhouse brand Ecovacs Robotics. With several excellent reviews already on TechRadar, including those by my colleague Sharmishta, who swears by the brand and rated the Ecovacs Deebot X8 Pro Omni very highly, I was eager to get stuck into my own assessment of the Deebot T90 Pro Omni, which launched in March this year.

On paper, it came across as the perfect pet-friendly robot vacuum. It touted an impressive 30,000Pa suction power across hardwood and carpeted floors, and as a mum to two Border Collies, cleaning up fur every day was my #1 priority.

It also didn't help that I fell pretty hard for The T90's looks (more on that below), but I was anxious about its price — $899.99 / £899 / AU$2,299 seemed rather steep, especially in Australia where I'm based, for a T-series Deebot that's typically been the more mid-range option to Ecovacs' X-series flagships. But then you get what you pay for, right? Or so I thought.

After using it for three months, I was left with an expensive robot vacuum that still looks lovely in its corner but doesn't quite fulfil the rest of its promises.

It's a looker

If you’ve often considered a robot vacuum, but have been put off by the large, rather unsightly docking stations, then you’ll be pleased to learn that the Deebot T90 Pro arrives with the newly enhanced Ecovacs station. The dock and station's combined footprint is slim, and it can easily be placed under a counter or table if you want to store it away. But given its Nordic-inspired, fabric-like design, Ecovacs clearly didn't intend for the T90 to be hidden, especially in homes with minimalist aesthetic settings. Personally, I quite liked the new off-white color as it complemented my apartment decor.

Unlike some other Ecovacs' robot vacuums, the T90 Pro Omni's bot neglects a turret completely, opting for a LiDAR sensor at the front of the machine, so it can get under furniture without issues. In place of a turret sits a loosely placed fabric-like lid that can, sadly, get dislodged when bumped into with some force.

However, the fact that both water tanks are fully concealed within the dock is a big tick for me, as it means I never once had to catch sight of dirty water throughout the day. The trade-off to this is that you can't see if either tank is full or empty. If you set the robot vacuum to clean everyday, then you’ll need to regularly check the tanks to see if they need filling or emptying.

I found I was consistently emptying and refilling the water tanks after every other clean despite its 4L capacity and the mopping area in my apartment is the living, dining and kitchen (my bedrooms are carpeted). I'm also a little surprised that the dirty-water capacity is so much lower, I was expecting it to be around 3L. What that means is, if you live in a large family home, you'll likely need to clean out the dirty mop water between each session too — beats the purpose I think.

Looks can be deceiving

It's lovely design aside, the T90 Pro struggled from day one, starting with its initial floor mapping. As I've already mentioned, my single-storey apartment has a mixture of carpeted and hardwood floors and a relatively straightforward floor plan, which most robovacs I've tried can get right the first time. Nevertheless, it took six mapping sessions to finally achieve an accurate map of my home.

I'll take some of the blame here, as the one map error was my fault after leaving my built-in wardrobe open, but I wanted to believe that after considerable daily use, the bot would update the floorplan on its own — I suppose I was expecting too much from Ecovacs' software there.

Even after the T90 had mapped my home accurately, I still had to make significant edits in the app to get all the rooms marked out correctly, something I've not had to do with other brands.

I made sure all carpet areas were marked out and, despite that, the T90 Pro Omni repeatedly mopped the bedrooms when in Auto mode to do a full-house clean. The only way to avoid this was to start setting up Room or Zone cleans every single time. In other words, the Auto Mode, for me, was redundant.

Aside from the copious amounts of remapping and wrong floor recognition, the T90 faltered when it came to vacuuming up pet hair. Despite its high suction power, I found that the T90 consistently left pet hair on even my hard floors (struggling even more on carpets), and I had to do a follow-up clean with my Dreame U20 which, even as affordable cordless option without a lot of suction, does so much better.

This really was my biggest disappointment because Ecovacs' Blast suction promises improved airflow for the best clean and I saw no evidence of that here. Moreover, a lot of the pet hair got entangled in the central bar brush and its wheels, meaning the bot itself required constant maintenance.

Mopping was a rather unfortunate experience too, especially after all those trips to and from the tap. My wood floors were left streaky and some spills were ignored by the AI stain recognition. My colleague Sharm much prefers the roller mops to the rotating discs on robovacs, but I'm not convinced... yet.

Random starts was another issue I had to face with the T90 Pro Omni — it would just start cleaning on its own, even when there was no voice command or a schedule set up.

There was a silver lining in all this, though: despite being a little basic compared to other robot vacuum apps I've used, the Ecovacs Home app was fairly easy to use (after the remapping shenanigans of course) to set up custom cleaning routines, schedules, suction and waterflow rates.

The easy-to-use app doesn't make up for everything else that went wrong though.

So, what now?

Look, I'll be honest — I was hard-pressed to find something positive to say about the Ecovacs Deebot T90 Pro Omni. A nice design and a decent app will only take my over user experience so far.

I wasn't looking for perfection; I just needed a robot vacuum that do the daily cleanup so I didn't have to and, in that one task, the T90 failed as I had to vacuum again anyway.

And this isn't the first time a Deebot has disappointed — my colleague Sharm wasn't particularly enthused by the older Ecovacs Deebot T50 Max Pro Omni either. TechRadar's recently published Ecovacs Deebot X12 Omnicyclone review also doesn't look very encouraging.

So what's going on at Ecovacs Robotics, one of the pioneering robovac brands? The company's been pumping out new models in quick succession over the last few years, with three alone announced at CES 2026, but it just feels like software and performance issues aren't being fully tested before release to market. Maybe it's time for Ecovacs to slow down, take a beat, and perhaps learn from its mistakes before releasing another suite of subpar products.

I'm still keeping faith that the brand will impress me one day, it's just not going to be with the T90 Pro Omni.

• Planning permission isn't usually required unless you're in a conservation area or listed building
• Cooling-only systems aren't covered by permitted development rules
• If in doubt, speak to your council

If you're looking for a way to avoid the sweltering heat of yet another heatwave arriving soon, air conditioning looks awfully tempting – so much so that in the UK, portable AC units are sold out almost everywhere or going for silly money on eBay, while air con installers are booked far into the future.

With future summers expected to get even hotter, many of us are now looking into fully installed AC as a long-term investment for our homes and our health, and that means we're likely to encounter a lot of confusion and misinformation about what you can and cannot do under UK planning and building regulations.

That confusion has been partly fuelled by social media and very misleading newspaper headlines suggesting that Net Zero-crazed councils are demanding innocent homeowners 'RIP OUT' their expensive installations.

The UK government's ministry of housing, communities and local government (MHCLG) says that such coverage is incorrect. "In most cases, planning permission is not required to install [air con] for a small home if it would not materially effect the appearance of the building from outside."

The most sensational headlines have been about air con in London and reference the London Plan, a city-specific rule that prioritises passive cooling and discourages extensive use of air con due to the heat it emits outside, which can contribute to heat islands in built-up areas.

As a spokesperson for the Mayor of London told The Telegraph: "The current London Plan does not rule out air conditioning — its policy is only applicable to major developments and requires new developments to address overheating risk from the outset — through measures such as shading, ventilation and other cooling design features."

If you look at the detail of the newspaper stories you'll typically find that the problem wasn't the air con itself, but how and where it was installed.

The problem is that even the the Government's press release above saying "Air conditioning units are not banned" also then says "However, there is no blanket rule. People should speak with their local council to check the rules, and councils should take a common-sense approach." So that' doesn't exactly totally clear things up — but there are basic rules that apply broadly, which are then changed depending on the local council situation.

So here's an overview of what rules you need to know about when you're considering investing in permanent air conditioning, so you at least know where you're starting from, and you can look into your area's circumstances from there.

In this article we'll be focusing exclusively on adding domestic air con to an existing residential home that you own. If your home is a leasehold in England you may need to obtain the freeholder's consent in addition to the other criteria.

What kind of home you have matters

The rules depend very much on what kind of home you have. If you're in a listed building you'll definitely need to apply for listed building consent; if you're in a conservation area, there will be restrictions on changing the appearance of your home, so there will be limits as to where you can place the external unit on the outside of your home.

If your home is neither listed nor in a conservation area, then the rules are largely common sense: under the rules for 'Permitted Developments' you don't need planning permission provided your air con meets some reasonably straightforward technical and location criteria.

The specific criteria are similar across the UK and I've linked to them here:

• England
• Scotland
• Wales
• Northern Ireland

If you're not sure if your system meets the permitted development criteria, we'd strongly recommend a chat with your local council's planning department: get it wrong and the council can make you remove the system at your own expense. You don't want to make what could be a very expensive mistake.

What are the core rules for home air conditioners in the UK?

The basic rules (before you get into conversation areas, and so on) differ depending on the kind of air conditioning you're thinking of installing.

If your air conditioner can heat as well as cool then it's generally allowed under Permitted Development rules under their Class G permissions, which are enforced by your local council on a common-sense basis.

Provided your external condenser unit (the part of an installed air con that goes outdoors) or heat pump isn't too big, too loud, too visible or too close to your neighbours, you don't usually need planning permission.

That's not the case if the air conditioner cools but doesn't also have a heating element. You need planning permission for that, and councils are keen to discourage such installations.

How big can your aircon be in the UK?

The Class G permissions allow you to install air con on your property or its "curtilage", which is the land associated with and immediately surrounding it including additional buildings. If you live in a castle the curtilage is anything inside the castle walls; if you're in a semi-detached the curtilage usually means your garden, driveway and garage, if you have one.

Most modern air con systems are Air Source Heat Pumps (ASHP), which means they can both cool and heat the air they take in and expel.

The Class G permissions were revised in 2025 to specifically include the exterior units of ASHPs, and they state that in a permitted development:

• You can have up to two ASHPs on a detached house or bungalow
• If you live in a semi-detached or terraced house, you may only have one ASHP
• If you live in a block of two flats or more, that also limits you to one ASHP

For a terraced, semi-detached or detached house the ASHP must not be bigger than 1.5 cubic metres. For flats the limit is 0.6 cubic metres.

A cubic metre is 1m wide, 1m tall and 1m deep. That's bigger than a freestanding fridge: sizes differ by manufacturer and product, but as an example the outdoor units for Toshiba's current RAS multi-split air conditioners range from 0.12m³ to 0.25m³ with the very largest model coming in at 890 x 900 x 320mm — that fits easily within the house regulations.

What kind of air conditioner can I install?

Under Class G your equipment must comply with the Microgeneration Certification Scheme, or MCS for short. The regulations are a bit odd here because while an air source heat pump must comply with the MCS, it doesn't need to have a certificate. The details of the MCS are online here.

Where can I install my air conditioner?

The rule preventing you from installing your external unit within 1m of neighbouring properties has been scrapped. However, your installation must not negatively impact your neighbours with noise: the noise level of your external unit cannot exceed 42 decibels measured at one metre from your nearest neighbour's front door or window. MCS-compliant units will not exceed that limit.

You can't install the external unit on a pitched roof, or within a metre of the edge of a flat roof.

If you're not in a conservation area or listed building, you may install the external unit on the front wall provided it's on the ground floor.

If you're in a conservation area you cannot install an external unit on any elevation that faces a highway.

The location of your external unit is where the common-sense criteria come in: the external unit, its cabling and any ducting must be sited in such a way that it is "so far as practicable, sited so as to minimise its effect on the external appearance of the building" and sited "so as to minimise its effect on the amenity of the area".

If you have a wind turbine in your garden you're out of luck: Class G doesn't give permission for any air con installation for properties with a turbine within their curtilage.

Your air con installer will be well aware of the regulations and should be able to ensure that your air con meets all the relevant requirements, but if you have any doubts please do talk to your local council's planning officers, because again you really don't want them to actually have cause to force you to remove it.

What do I do to make sure there aren't special rules in my area?

Your council will likely have a whole website dedicated to helping with planning information, including potentially a map showing whether your home is included in any conservation areas, and what the specific orders around those areas are, so you can work out whether they'd affect air con installation.

If not, or if it's still unclear, you council will have a system for enquiries around planning permission, so you can ask if what you're planning needs a permit without going through the process — and it means that if you need one, they can tell you exactly what's needed.

Forget BBQs, I'm all about outdoor pizzas this year. If you want to hop on the homemade pizza bandwagon (welcome, there's plenty of space!), then now's a good time to get yourself set up with a pizza oven. Making your own pizzas is fun and satisfying, and the results are so much more delicious than oven pizzas or takeaway. If you're short on time or not especially gifted in the kitchen, it's pretty easy to find premade dough base balls that you can just roll out and add toppings to (this is my preferred method).

When picking a pizza oven, your main decision will be the type of fuel you want it to run on. Most modern pizza ovens — including the one I have at home — run on gas, which is speedy, convenient, and easy to control by just adjusting a dial. Another option is to opt for wood, which gives that delicious smokey smell and taste (although your pizzas won't be cooking for very long, so the impact won't be massive), but requires more effort to control the temperature.

There are a few 'multi-fuel' pizza ovens that can be used with either wood or gas. Alternatively, you could opt for an electric pizza oven. These are ultra-convenient, easy to control and versatile too. However, they tend not to get as hot as the other options, and you lose that authentic experience and charred flavor.

Below, I've rounded up some of our favorite pizza ovens. If you want to see how these options compare, hop to the bottom of the page for a specs comparison table.

Gas pizza ovens

I tend to think of gas pizza ovens as a 'happy medium' option. They can reach scorching temperatures, so you'll get those authentic charred edges, but are reliable to use and it's easy to adjust the heat up or down.

You won't get the 'smokey' wood-fired flavor — however, given your pizza's only going to be in there for a couple of minutes max, the difference isn't going to be nearly as noticeable as, for instance, using a gas versus charcoal BBQ.

Wood fired pizza ovens

Wood fired pizza ovens run on pellets. Like gas options, they can get super-hot, but controlling the temperatures is trickier — it requires adjusting the vents and adding fuel. You'll also need to deal with the ash leftover afterwards. However, you will get the delicious smokey smell, and a more traditional cooking experience.

Electric pizza ovens

An electric pizza oven won't give you that unique cooking experience; instead, it'll be a lot more like using an air fryer or regular oven. They also tend not to have a lower maximum temperature, so it's trickier to achieve those crispy bases and charred edges. However, what you lose in authenticity you gain in convenience — you can control temperatures precisely, and the results are very predictable.

Multi-fuel pizza ovens

Pizza oven specs compared

If you've been checking the weather forecast, you'll have noticed that the temperature is set to rise again next week. It might not reach the scorching highs of 40C, but much of the UK is still going to be hot and sticky, so it's wise to grab a fan before stock flies off the virtual shelves again.

• Today's fan deals at Amazon

Lots of fans completely sold out last week (some won't be back in stock until October), but there are some great deals on models from big brands if you know where to look. I've scoured the web and found six particularly good offers from reputable brands, so you don't end up settling for less than the best.

My personal pick is the Dimplex FlexBlade Bladeless Tower Fan, which is now £159.99 at Amazon (was £199.99), and kept me comfortable the last time the temperatures soared. You can aim this fan at your bed, and it's quiet enough not to disturb your sleep.

Want more recommendations? Take a look at our full guide to the best fans for all the top models we've tested in our own homes, and which have earned our seal of approval.

• Google Home Speaker users are reporting early issues
• The voice assistant is taking up to 60 seconds to respond to requests
• Google has said it's working on a fix, but there hasn't been any updates

Google has only just returned to smart hubs with its new AI-powered Google Home Speaker, six long years after the company released the Nest Audio — and users are already running into issues.

It’s been barely a week since pre-orders were shipped and those who’ve been excited to test out the upgraded Google Home Speaker have been let down with the device’s performance.

The crux of the issue is the voice assistant itself, which many users say takes a while to respond to their commands. A slew of Reddit posts highlight the same issue, agreeing that the speaker can take between 30-60 seconds before responding, and others have experienced audio cutting out altogether.

Google Speaker 2026 from r/googlehome

While we don’t know how widespread these lagged responses are, the top comment in the Reddit thread above says it’s happening globally. Whether this is the case or not, it’s birthed a lot of frustration among those who have spent good money on the new device — “I’m returning mine” one user writes, while another says “I really hope Google puts more effort into things”.

Looking at the user reactions, it appears that this issue is also prevalent in older devices like the Nest Audio and Nest Mini, so it’s not just the new Home Speaker that’s going through the ringer. Thankfully, Google is doing something about it.

Amidst the backlash, the official u/GoogleNestCommunity replied to the Reddit post with the following; “We're aware of an issue causing increased latency or timing out. We are working on a fix ASAP and will circle back once this is resolved. Thanks for your patience”.

Though Google’s acknowledgment provides some sort of reassurance that a fix is on the way, the company hasn’t provided any details on how it intends to address the issues or when users can expect to see an improvement. At this rate, it’s still a waiting game, but this isn’t the only run-in with criticism the Google Home Speaker has faced since its launch.

Repairability could be hindered

When Google officially announced the new Home Speaker in October 2025, I was thrilled to see a new speaker was on the way just as much as the next person, but there’s one setback which an early unboxing video addresses.

The Google Home Speaker has a fixed power cable, meaning you can’t disconnect it like you can with the majority of the best smart speakers. It may sound like we’re splitting hairs here, but the unboxing video highlights the repairability problem that comes with not having an unpluggable power cord.

These issues aside, the Google Home Speaker isn't totally devoid of positives. According to the same unboxing video, the speaker’s accompanying app has a lot of appeal and the overall audio quality is pretty solid — so it’s nice to see that Google has adhered to its 360-audio upgrade promises.